SsangYong: Engine Euro 4. Instruction - page 46
CHANGED BY
EFFECTIVE DATE
AFFECTED VIN
13
1491
DIAGNOSIS
D27DTP/D27DT (EU4) SM - 2006.08
D27DTP/D27DT (EU4)
ENGINE
FUEL
I
N
T
AKE
EXHAUST
PRE-HEA
TING
LUB
COOLING
SWITCHABLE
ECU
DIAGNOSIS
ڟگګٻڍڒڋڃڞڎڤڄ
ڮۃۄہۏٻڧۀۑۀۍٻڨېێۏٻڽۀದګಧګۊێۄۏۄۊۉ
ڮۃۄہۏٻڧۀۑۀۍٻڨېێۏٻڽۀದګಧګۊێۄۏۄۊۉ
1. [Select “1] LEAK DETECTION” and press
on
“MISCELLANEOUS SELECTION” screen.
2. The “LEAK DETECTION” screen showing the check-
ing conditions as shown in figure is displayed.
Leak Detection
Ú
Ú
Ú
Ú
Ú Preceding Work: Perform the “Entering Diagnosis
Procedures”
3. The pressure leakage check for fuel system should
be done under idling, and as the engine RPM is rais-
ing during the self test, the shift lever should be place
to “P” position.
• This item is for checking the high fuel pressure
after the IMV supply line of HP pump in DI engine
fuel system. If you still suspect that the fuel pres-
sure system is defective even after no trouble is
detected, perform the fuel pressure test again by
using a fuel pressure tool kit.
NOTE
CHANGED BY
EFFECTIVE DATE
AFFECTED VIN
14
1491
DIAGNOSIS
D27DTP/D27DT (EU4) SM - 2006.08
D27DTP/D27DT (EU4)
is automatically selected.
Select
only for the vehicle with PTC type supplementary
heater (in DI engine).
Only for the vehicle with auto cruise.
Select
only for the vehicle with immobilizer system.
No remote starter system is applied to this model. However,
must select
to confirm that this vehicle doesn't have
remote starter.
Select CAN.
Select
only for the vehicle with ABS or ESP system.
Select
only for the vehicle with TOD/part time 4WD.
* Select
for the vehicle with AWD or 2WD.
Select
only for the vehicle with A/C.
Select
.
Select only if the vehicle is equipped with manual transmis-
sion neutral switch.
: Automatic transmission equipped vehicle or
manual transmission neutral switch not equipped
vehicle (adopted the manual transmission neutral
switch for NEW REXTON from Sep 15, 20004)
: Adopted neutral switch among REXTON models
with manual transmission
: REXTON II, ACTYON, KYRON and RODIUS with
manual transmission (REXTON II is not equipped
with manual transmission)
- D27DTP (POWER UP) Engine: Select
.
- D27DT Engine: Select
.
- D27DTP (POWER UP) Engine: Select AQGS (CAN).
- D27DT Engine: Select Relay.
Description
Variant Coding Item
Selection
Variant Coding
For REXTON II, D27DTP (POWER UP) engine is newly adopted but the coding methods are almost same as the
variant coding items of the previous model. The variant coding items entering the vehicle information to the engine
ECU are changed a little. As the model for exporting and current model contain the unavailable items, it is necessary
to variant code to the engine ECU if the engine ECU or the ECU of other systems are replaced.
Most of all, you should check the variant coding items if the abnormal operation of any systems or errors occur.
1. Engine-related Coding Item
Coding Item
WIRE
NO
CAN
• As REXTON II D27DTP (POWER UP) engine is not equipped
with manual transmission, select
.
NOTICE
ECU coding completed
Supplementary heater (PTC)
Auto cruise
Immobilizer
Remote starter
Vehicle speed signal
ABS or ESP
TOD / Part time TCCU (4WD)
A/CON
PWM Condenser Fan
Neutral signal input
(M/T “N” signal)
Engine mount level control
(Switchable engine mounting)
Glow plug module
No/Yes
No/Yes
No/Yes
No/Yes
No/Yes
CAN/WIRE
No/Yes
No/Yes
No/Yes
No/Yes
No/Yes
(WIRE)/CAN
No/Yes
Relay/AQGS
(CAN)
CHANGED BY
EFFECTIVE DATE
AFFECTED VIN
15
1491
DIAGNOSIS
D27DTP/D27DT (EU4) SM - 2006.08
D27DTP/D27DT (EU4)
ENGINE
FUEL
I
N
T
AKE
EXHAUST
PRE-HEA
TING
LUB
COOLING
SWITCHABLE
ECU
DIAGNOSIS
2. Chassis Related Coding Item
Select the appropriate engine.
Select the region.
Select the appropriate item.
EAS (2): 2 corner EAS, EAS (4): 4 corner EAS
For vehicle with EPB, select
.
- Automatically selected (auto coding)
For vehicle with telematics, select
.
Select the appropriate selector lever.
For REXTON II, select the DURA lever.
Select the appropriate system.
If equipped, select
.
If equipped, select
.
Select the appropriate system.
Select the appropriate system.
Select the coding status.
Engine model
DOM/EXP
EAS
EPB
Telematics
Selector lever
ABS/ESP
SSPS
TPMS
Transfer case (4WD)
Transmission type
Coding
D27DTP/D27DT/D20DT
DOM/GENERAL/EU
NA/ECS/EAS (2)/EAS (4)
No/Yes
No/Yes
ION (BTRA)/DC lever/
DURA lever
NA/ABS/TCS/ESP
No/Yes
No/Yes
2WD / TOD / P/T 4WD /
AWD / P/T 4WD (non-4L)
M/T / DC5AT / ION (BTRA) AT
CODING COMPLETED
Variant Coding Item
Selection
Description
CHANGED BY
EFFECTIVE DATE
AFFECTED VIN
16
1491
DIAGNOSIS
D27DTP/D27DT (EU4) SM - 2006.08
D27DTP/D27DT (EU4)
• Please refer to the remarks (mentioned at the be-
ginning of the variant coding items) about the cod-
ing items related to engine and chassis.
NOTE
ڞڎڤ
ڞڎڤ
ڞڪکڡڤڭڨٻڠکڢڤکڠٻڱڜڭڤڜکگٻڞڪڟڤکڢ
ڞڪکڡڤڭڨٻڠکڢڤکڠٻڱڜڭڤڜکگٻڞڪڟڤکڢ
This descripes how to progress variant coding.
1. Select “7] VARIANT CODING” and press
on
“FUNCTION SELECTION” screen.
Coding Procedures
2. When the “VARIANT CODING” screen is displayed,
select “1] READ VARLANT VALVE” and press
.
3. Select the variant coding item related to the engine
or chassis.
4. The “VARIANT CODING” screen showing the currently
equipped devices is displayed.
• As the pictures are used to help the user to eas-
ily understand, they may be different from the ac-
tual procedures. Please follow the contents and
steps on SCAN-100 screens.
NOTICE