Dacia Solenza (engine E7J). Instruction - page 92
THE MECHANICAL ELEMENTS CONTROLS
37
37 - 18
DISMOUNTING
In the engine compartment :
- release the clutch cable (1) from the
clutch control fork.
- detach from carriage body clips the
clutch cable.
Clutch cable
TIGHTENING
MOMENTS
(Nm)
Clutch cable counter nut
8
In the cockpit:
- release the clutch cable (1) from the clutch
pedal cam and depress it from the pedals
support.
REMOUNTING
Perform the dismounting operations in the
reverse order.
Adjust the clutch control
CLUTCH CONTROL ADJUSTMENT
In order to adjust the clutch pedal stroke,
proceed as follows:
- place a gauge to ensure the 15 mm
clearance between the pedal and the pedals
support (4);
- tighten the nut (3) on the clutch cable
end, until obtaining a stroke of 29 ± 1 mm at
the clutch disengaging fork by acting upon the
clutch pedal;
- tighten the counter nut (2) to the
required moment of 8 Nm.
15
4
1
1
2 3
THE MECHANICAL ELEMENTS CONTROLS
37
37 - 19
DISMOUNTING
Dismount the nut and the lock nut from the clutch cable end.
Mount the buffer (1).
REPLACEMENT OF CLUTCH CABLE BUFFER
1
REMOUNTING
Remounting is done by performing the dismounting operations in the reverse order.
Adjust the clutch control ( see chapter 37 – “ Clutch control adjustment”).
Clutch cable
THE MECHANICAL ELEMENTS CONTROLS
37
37 - 20
DISMOUNTING
Disconnect :
- battery;
- stop contact connectors.
Dismount:
- clutch cable (3) from the pedal cam
(after it has been released from the clutch control
fork);
- servobrake ( see page 37 – 5);
- pedals support attachment nuts (1) on the
cowl panel;
Pedals support
- attachment screw (2) of the pedals
support to the welded support of the driving
post cross-beam;
- clutch pedal (4);
- brake pedal (5);
- stop contact (6).
Release the pedals support.
REMOUNTING
Perform the dismounting operations in the
reverse order.
Adjust the clutch control (see chapter 37
– Clutch control adjustment).
Check the operation of the stop contact.
THE MECHANICAL ELEMENTS CONTROLS
37
37 - 21
DISMOUNTING
Detach from clips the cable from the
acceleration pedal (3) by harpoon (5)
compressing.
Acceleration control
TIGHTENING MOMENTS (daNm)
Pedal bearing attachment nut 0.8
Dismount the bearing attachment nut (2) and
release the pedal.
REMOUNTING
Perform the dismounting operations in the
reverse order, taking into consideration the
following:
- before bearing (6) closing, grease the
contact parts with the pedal and check if the
pedal rotation in the bearing is done without
noises or locks;
- adjust the pedal stroke at the
“maximum” position of the valve, which is
obtained by pushing the pedal until pressing on
the limiting part (4).
- the tightening moment of the pedal
bearing attachment nut is of 0.8 daNm.
ACCELERATION CABLE
Detach from clips the cable from the
acceleration pedal (3) by harpoon (5)
compressing.
Release the acceleration cable (1) from the
valve lever (A).
Detach from clips the acceleration cable and
release it.
REMOUNTING
First attach the acceleration cable to the
valve lever (A), and then attach by clips the
other end on the acceleration pedal arm.
Push the acceleration pedal until pressing on
the limiting part (4) (2-3 pushing). In this
position, the length adjustment is done.
In case of the buffer replacement (6), the
clip from the cable is to be placed at a 34 mm
position and after that, the a.m. adjustment is
to be performed.
ACCELERATION PEDAL