Nissan 370Z Roadster (2017 year). Instruction - part 8

(114,1)

[ Edit: 2016/ 2/ 22

Model: 2017MY NISSAN 370Z(Z34) OM17E00Z34U0 ]

2-46

Instruments and controls

of about 45 seconds, power to the windows is
canceled.

The power window switches will be deactivated
during soft top operation (Roadster models).

JVI1248X

1.

Driver side window

2.

Front passenger side window

3.

Window lock button

Main power window switch (driver’s
side)

To open or close the window, push down

*

A

or

pull up

*

B

the switch and hold it. The main

switch (driver side switches) will open or close
all the windows.

Locking passengers’ window

When the lock button

*

C

is pushed in, only the

driver side window can be opened or closed.
Push it in again to cancel.

Condition:

(115,1)

[ Edit: 2016/ 2/ 22

Model: 2017MY NISSAN 370Z(Z34) OM17E00Z34U0 ]

SIC3241

Passenger side power window switch

The passenger side switch will open or close
only the corresponding window. To open or
close the window, push down or pull up the
switch and hold it.

JVI1203X

Automatic operation

To fully open or close the window, completely
push down or pull up the switch and release it; it
need not be held. The window will automatically
open or close all the way. To stop the window,
just push or lift the switch in the opposite
direction.

A light push or pull on the switch will cause the
window to open or close until the switch is
released.

Auto reverse function

WARNING

There are some small distances imme-
diately before the closed position which
cannot be detected. Make sure that all
passengers have their hands, etc., in-
side the vehicle before closing the
window.

If the control unit detects something caught in
the window as it is closing, the window will be
immediately lowered.

The auto reverse function can be activated when
the window is closed by automatic operation
when the ignition switch is in the ON position or
for 45 seconds after the ignition switch is
pushed to the OFF position.

Depending on the environment or driving
conditions, the auto reverse function may
be activated if an impact or load similar to
something being caught in the window
occurs.

Instruments and controls

2-47

Condition:

(116,1)

[ Edit: 2016/ 2/ 22

Model: 2017MY NISSAN 370Z(Z34) OM17E00Z34U0 ]

2-48

Instruments and controls

Automatic window lowering (Roadster
models)

When the soft top operating switch is pressed,
the power windows will automatically be low-
ered completely. The windows do not rise
automatically after the soft top open/close
operation is completed. Use the power window
switches to raise them.

Automatic adjusting function

CAUTION

When the battery cable is removed from
the battery terminal, do not close either
of the front doors. The automatic win-
dow adjusting function will not work
and the side roof panel may be da-
maged.

The power window has an automatic adjusting
function. When the door is being opened, the
window is automatically lowered slightly to avoid
contact between the window and the side roof
panel. When the door is closed, the window is
automatically raised slightly.

While the automatic adjusting function does not
work, the window will be controlled as follows:

.

When the door is opened, the window
lowers for approximately 2 seconds.

.

While the door is open, the window cannot
be raised.

If the windows do not close automatically

If the power window automatic function (closing
only) does not operate properly, perform the
following procedure to initialize the power
window system.

1. Push the ignition switch to the ON position.

2. Close the door and soft top (Roadster

models).

3. Open the window completely by operating

the power window switch.

4. Pull the power window switch and hold it to

close the window, and then hold the switch
more than 3 seconds after the window is
closed completely.

5. Release the power window switch. Operate

the window by the automatic function to
confirm the initialization is complete.

6. Perform steps 2 through 5 above for other

windows.

If the power window automatic function does
not operate properly after performing the pro-
cedure above, have your vehicle checked. It is
recommended you visit a NISSAN dealer for this

service.

Condition:

(117,1)

[ Edit: 2016/ 2/ 22

Model: 2017MY NISSAN 370Z(Z34) OM17E00Z34U0 ]

SIC4238

MAP LIGHTS

Push the button as illustrated to turn the light on
or off.

SIC4239

INTERIOR LIGHT CONTROL SWITCH

The interior light control switch has three
positions: ON, DOOR and OFF.

ON position

When the switch is in the ON position

*

1

the

map lights will illuminate.

DOOR position

When the switch is in the DOOR position

*

2

,

the map lights will illuminate under the following
conditions:

.

ignition switch is switched to the OFF or
LOCK position

— remain on for about 15 seconds.

.

doors are unlocked by pushing the UN-
LOCK button on the Intelligent Key or door
handle request switch with the ignition
switch in the LOCK position

— remain on for about 15 seconds.

.

any door is opened and then closed with the
ignition switch in the LOCK position

— remain on for about 15 seconds.

.

any door is opened with the ignition switch
in the ACC or ON position

— remain on while the door is opened.

When the door is closed, the lights go
off.

The lights will also turn off after a period of
time when the lights remain illuminated
after the ignition switch has been pushed
to the OFF or LOCK position to prevent the
battery from becoming discharged.

Models with navigation system:

When the auto interior illumination is set to the
OFF position (see “Vehicle information and
settings (models with navigation system)” (P.4-
8)), the lights will illuminate under the following
condition:

.

any door is opened with the ignition switch
in any position

Instruments and controls

2-49

INTERIOR LIGHTS

Condition:

(118,1)

[ Edit: 2016/ 2/ 22

Model: 2017MY NISSAN 370Z(Z34) OM17E00Z34U0 ]

2-50

Instruments and controls

— remain on while the door is opened.

When the door is closed, the lights go
off.

OFF position

When the switch is in the OFF position

*

3

, the

lights will not illuminate, regardless of the
condition.

CAUTION

Do not use for extended periods of time
with the engine stopped. This could
result in a discharged battery.

SIC3869

The light on the vanity mirror will turn on when
the cover on the vanity mirror is opened.

When the cover is closed, the light will turn off.

The lights will also turn off after a period of
time when the lights remain illuminated to
prevent the battery from becoming dis-
charged.

The light illuminates simultaneously with the map
light. See “Interior lights” (P.2-49).

VANITY MIRROR LIGHTS

CARGO AREA COURTESY LIGHT
(Roadster models)

Condition:

(119,1)

[ Edit: 2016/ 2/ 22

Model: 2017MY NISSAN 370Z(Z34) OM17E00Z34U0 ]

The light illuminates when the rear hatch is
opened. When the rear hatch is closed, the light
will turn off.

The light will also turn off after a period of
time when the light remains illuminated
after the ignition switch has been pushed
to the OFF or LOCK position to prevent the
battery from becoming discharged.

The light illuminates when the trunk lid is
opened. When the trunk lid is closed, the light
turns off.

The HomeLink

®

Universal Transceiver provides a

convenient way to consolidate the functions of
up to three individual hand-held transmitters into
one built-in device.

HomeLink

®

Universal Transceiver:

.

Will operate most Radio Frequency (RF)
devices such as garage doors, gates, home
and office lighting, entry door locks and
security systems.

.

Is powered by your vehicle’s battery. No
separate batteries are required. If the
vehicle’s battery is discharged or is dis-
connected, HomeLink

®

will retain all pro-

gramming.

When the HomeLink

®

Universal Transcei-

ver is programmed, retain the original
transmitter for future programming proce-
dures (Example: new vehicle purchases).
Upon sale of the vehicle, the programmed
HomeLink

®

Universal Transceiver buttons

should be erased for security purposes.
For additional information, refer to “Pro-
gramming HomeLink

®

” (P.2-52).

WARNING

.

Do not use the HomeLink

®

Universal

Transceiver with any garage door
opener that lacks safety stop and

Instruments and controls

2-51

CARGO LIGHT (Coupe models)

TRUNK LIGHT (Roadster models)

HomeLink

®

UNIVERSAL

TRANSCEIVER (if so equipped)

Condition:

(120,1)

[ Edit: 2016/ 2/ 22

Model: 2017MY NISSAN 370Z(Z34) OM17E00Z34U0 ]

2-52

Instruments and controls

reverse features as required by
federal safety standards. (These
standards became effective for
opener models manufactured after
April 1, 1982). A garage door opener
which cannot detect an object in the
path of a closing garage door and
then automatically stop and reverse,
does not meet current federal safety
standards. Using a garage door
opener without these features in-
creases the risk of serious injury or
death.

.

During the programming procedure
your garage door or security gate
will open and close (if the transmit-
ter is within range). Make sure that
people or objects are clear of the
garage door, gate, etc. that you are
programming.

.

Your vehicles engine should be
turned off while programming the
HomeLink

®

Universal Transceiver.

Do not breathe exhaust gases; they
contain colorless and odorless car-
bon monoxide. Carbon monoxide is
dangerous. It can cause uncon-
sciousness or death.

PROGRAMMING HomeLink

®

If you have any questions or are having difficulty
programming your HomeLink

®

buttons, refer to

the HomeLink

®

web site at: www.homelink.com

or call 1-800-355-3515.

NOTE:

It is also recommended that a new battery
be placed in the hand-held transmitter of
t h e d e v i c e

b e i n g p r o g r a m m e d

t o

HomeLink

®

for quicker programming and

accurate transmission of the radio-fre-
quency.

1. Position the end of your hand-held transmit-

ter 1-3 in (26-76 mm) away from the
HomeLink

®

surface, keeping the HomeLink

®

indicator light

*

1

in view.

JVI0428X

2. Using both hands, simultaneously press and

hold the desired HomeLink

®

button and

handheld transmitter button. DO NOT re-
lease until the HomeLink

®

indicator light

*

1

flashes slowly and then rapidly. When the
indicator light flashes rapidly, both buttons
may be released. (The rapid flashing indi-
cates successful programming.)

NOTE:
Some devices to be programmed may
require you to replace Step 2 with the
cycling procedure noted in the
Pro-
gramming HomeLink

®

for Canadian

customers and gate openers(P.2-53).

Condition:

(121,1)

[ Edit: 2016/ 2/ 22

Model: 2017MY NISSAN 370Z(Z34) OM17E00Z34U0 ]

JVI0429X

3. Press and hold the programmed HomeLink

®

button and observe the indicator light.

.

If the indicator light

*

1

is solid/contin-

uous, programming is complete and your
device should activate when the
HomeLink

®

button is pressed and re-

leased.

.

If the indicator light

*

1

blinks rapidly for

two seconds and then turns to a solid/
continuous light, continue with Steps 4-6
for a rolling code device. A second
person may make the following steps
easier. Use a ladder or other device. Do
not stand on your vehicle to perform the
next steps.

4. At the receiver located on the garage door

opener motor in the garage, locate the
“learn” or “smart” button (the name and
color of the button may vary by manufacturer
but it is usually located near where the
hanging antenna wire is attached to the
unit). If there is difficulty locating the button,
reference the garage door opener’s manual.

5. Press and release the “learn” or “smart”

button.

NOTE:
Once the button is pressed, you have
approximately 30 seconds to initiate
the next step.

6. Return to the vehicle and firmly press and

hold the programmed HomeLink

®

button for

two seconds and release. Repeat the
“press/hold/release” sequence up to 3
times to complete the programming pro-
cess. HomeLink

®

should now activate your

rolling code equipped device.

7. If you have any questions or are having

difficulty programming your HomeLink

®

but-

tons, refer to the HomeLink

®

web site at:

www.homelink.com or call 1-800-355-
3515.

PROGRAMMING HomeLink

®

FOR CA-

NADIAN CUSTOMERS AND GATE
OPENERS

Canadian radio-frequency laws require trans-
mitter signals to “time-out” (or quit) after several
seconds of transmission – which may not be
long enough for HomeLink

®

to pick up the signal

during programming. Similar to this Canadian
law, some U.S. gate operators are designed to
“time-out” in the same manner.

If you live in Canada or you are having difficulties
programming a gate operator or garage door
opener by using the “Programming HomeLink

®

procedures, replace “Programming HomeLink

®

Step 2 with the following:

NOTE:

When programming a garage door opener,
etc., unplug the device during the
cycling
process to prevent possible damage to the
garage door opener components.

Step 2: Using both hands, simultaneously press
and hold the desired HomeLink

®

button and the

hand-held transmitter button. During program-
ming, your hand-held transmitter may automati-
cally stop transmitting. Continue to press and
hold the desired HomeLink

®

button while you

press and re-press (“cycle”) your hand-held
transmitter every two seconds until the fre-
quency signal has been learned. The HomeLink

®

Instruments and controls

2-53

Condition:

(122,1)

[ Edit: 2016/ 2/ 22

Model: 2017MY NISSAN 370Z(Z34) OM17E00Z34U0 ]

2-54

Instruments and controls

indicator light will flash slowly and then rapidly
after several seconds upon successful program-
ming. DO NOT release until the HomeLink

®

indicator light flashes slowly and then rapidly.
When the indicator light flashes rapidly, both
buttons may be released. The rapid flashing
indicates successful programming.

Proceed with “Programming HomeLink

®

” step 3

to complete.

Remember to plug the device back in when
programming is completed.

OPERATING THE HomeLink

®

UNIVER-

SAL TRANSCEIVER

The HomeLink

®

Universal Transceiver, after it is

programmed, can be used to activate the
programmed device. To operate, simply press
and release the appropriate programmed
HomeLink

®

Universal Transceiver button. The

amber indicator light will illuminate while the
signal is being transmitted.

For convenience, the hand-held transmitter of
the device may also be used at any time.

PROGRAMMING TROUBLESHOOT-
ING

If the HomeLink

®

does not quickly learn the

hand-held transmitter information:

.

replace the hand-held transmitter batteries
with new batteries.

.

position the hand-held transmitter with its
battery area facing away from the
HomeLink

®

surface.

.

press and hold both the HomeLink

®

and

hand-held transmitter buttons without inter-
ruption.

.

position the hand-held transmitter 1-3 in
(26-76 mm) away from the HomeLink

®

surface. Hold the transmitter in that position
for up to 15 seconds. If HomeLink

®

is not

programmed within that time, try holding the
transmitter in another position - keeping the
indicator light in view at all times.

If you have any questions or are having difficulty
programming your HomeLink

®

buttons, refer to

the HomeLink

®

web site at: www.homelink.com

or 1-800-355-3515.

CLEARING THE PROGRAMMED IN-
FORMATION

The following procedure clears the programmed
information from both buttons. Individual buttons
cannot be cleared. However, individual buttons
can be reprogrammed, see “Reprogramming a
single HomeLink

®

button” (P.2-54).

To clear all programming

1. Press and hold the two outer HomeLink

®

buttons until the indicator light begins to
flash in approximately 10 seconds. Do not
hold for longer than 20 seconds.

2. Release both buttons.

HomeLink

®

is now in the programming mode

and can be programmed at any time beginning
with “Programming HomeLink

®

” - Step 1.

REPROGRAMMING A SINGLE
HomeLink

®

BUTTON

To reprogram a HomeLink

®

Universal Transcei-

ver button, complete the following.

1. Press and hold the desired HomeLink

®

button. DO NOT release the button.

2. The indicator light will begin to flash after 20

seconds. Without releasing the HomeLink

®

button, proceed with “Programming
HomeLink

®

” - Step 1.

Condition:

(123,1)

[ Edit: 2016/ 2/ 22

Model: 2017MY NISSAN 370Z(Z34) OM17E00Z34U0 ]

For questions or comments, contact HomeLink

®

at: www.homelink.com or 1-800-355-3515.

The HomeLink

®

Universal Transceiver button

has now been reprogrammed. The new device
can be activated by pushing the HomeLink

®

button that was just programmed. This proce-
dure will not affect any other programmed
HomeLink

®

buttons.

IF YOUR VEHICLE IS STOLEN

If your vehicle is stolen, you should change the
codes of any non-rolling code device that has
been programmed into HomeLink

®

. Consult the

Owner’s Manual of each device or call the
manufacturer or retailer of those devices for
additional information.

When your vehicle is recovered, you will
need to reprogram the HomeLink

®

Univer-

sal Transceiver with your new transmitter
information.

FCC Notice:

For USA:

This device complies with Part 15 of the
FCC Rules. Operation is subject to the
following two conditions: (1) This device
may not cause harmful interference, and
(2) this device must accept any interfer-
ence received, including interference that
may cause undesired operation.

NOTE:

Changes or modifications not expressly
approved by the party responsible for
compliance could void the user’s authority
to operate the equipment.

For Canada:

This device complies with Industry Canada
licence-exempt RSS standard(s). Opera-
tion is subject to the following two condi-
tions: (1) this device may not cause
interference, and (2) this device must
accept any interference, including interfer-
ence that may cause undesired operation
of the device.

Instruments and controls

2-55

Condition:

(124,1)

[ Edit: 2016/ 2/ 22

Model: 2017MY NISSAN 370Z(Z34) OM17E00Z34U0 ]

2-56

Instruments and controls

MEMO

Condition:

(125,1)

[ Edit: 2016/ 2/ 22

Model: 2017MY NISSAN 370Z(Z34) OM17E00Z34U0 ]

3 Pre-driving checks and adjustments

Keys .............................................................................................. 3-2

Intelligent Key ....................................................................... 3-2
Valet hand-off ....................................................................... 3-3

Doors ............................................................................................ 3-4

Locking with mechanical key ............................................ 3-4
Opening and closing windows with the
mechanical key ..................................................................... 3-4
Locking with inside lock knob .......................................... 3-5
Locking with power door lock switch ............................ 3-5
Automatic door locks ......................................................... 3-5

Intelligent Key system .............................................................. 3-6

Intelligent Key operating range ....................................... 3-8
Door locks/unlocks precaution ....................................... 3-8
Intelligent Key operation .................................................... 3-9
Battery saver system ....................................................... 3-11
Warning signals ................................................................ 3-11
Troubleshooting guide ..................................................... 3-12

Remote keyless entry system ............................................. 3-13

How to use remote keyless entry system .................. 3-13

Hood .......................................................................................... 3-16
Rear hatch (Coupe models) ............................................... 3-17

Rear hatch opener switch .............................................. 3-17
Secondary rear hatch release ....................................... 3-18

Trunk lid (Roadster models) ............................................... 3-19

Trunk lid opener switch ................................................ 3-19
Trunk release power cancel switch ........................... 3-20
Interior trunk lid release ................................................ 3-20
Secondary trunk lid release ......................................... 3-21

Soft top (Roadster models) ................................................ 3-21

Before operating the top .............................................. 3-21
When operating the top ............................................... 3-23
Opening the top ............................................................. 3-25
Closing the top ............................................................... 3-26
Opening the top using the Intelligent Key ............... 3-26
Troubleshooting guide .................................................. 3-27
If the top does not open or close electrically ......... 3-28
Care of the soft top and the vehicle body .............. 3-32

Front, side and rear unique parts (NISMO models) ..... 3-32
Fuel-filler door ........................................................................ 3-34

Opening the fuel-filler door ......................................... 3-34
Fuel-filler cap .................................................................. 3-34

Tilt steering ............................................................................. 3-36

Manual operation ............................................................ 3-36

Sun visors ................................................................................ 3-36
Mirrors ...................................................................................... 3-37

Inside mirror ..................................................................... 3-37
Outside mirrors ............................................................... 3-38
Vanity mirror ..................................................................... 3-39

Condition:

(126,1)

[ Edit: 2016/ 2/ 22

Model: 2017MY NISSAN 370Z(Z34) OM17E00Z34U0 ]

3-2

Pre-driving checks and adjustments

A key number plate is supplied with your keys.
Record the key number and keep it in a safe
place (such as your wallet), not in the vehicle. If
you lose your keys, it is recommended you visit a
NISSAN dealer for duplicates by using the key
number. NISSAN does not record any key
numbers so it is very important to keep track of
your key number plate.

A key number is only necessary when you have
lost all keys and do not have one to duplicate
from. If you still have a key, it can be duplicated
without knowing the key number.

SPA2406

1.

Intelligent Keys (2)

2.

Mechanical keys (inside the Keys) (2)

3.

Key number plate (1)

INTELLIGENT KEY

Your vehicle can only be driven with the
Intelligent Keys which are registered to your
vehicle’s Intelligent Key system components and
NISSAN Vehicle Immobilizer System compo-
nents. As many as 4 Intelligent Keys can be
registered and used with one vehicle. The new
keys must be registered by a NISSAN dealer
prior to use with the Intelligent Key system and
NISSAN Vehicle Immobilizer System of your
vehicle. Since the registration process requires
erasing all memory in the Intelligent Key compo-

nents when registering new keys, be sure to take
all Intelligent Keys that you have to the NISSAN
dealer.

It is possible that the Intelligent Key functions
become canceled. Contact a NISSAN dealer.

CAUTION

.

Be sure to carry the Intelligent Key
with you when driving. The Intelli-
gent Key is a precision device with a
built-in transmitter. To avoid dama-
ging it, please note the following.

— The Intelligent Key is water

resistant; however, wetting may
damage the Intelligent Key. If
the Intelligent Key gets wet,
immediately wipe until it is com-
pletely dry.

— Do not bend, drop or strike it

against another object.

— If the outside temperature is

below 148F (-108C) degrees, the
battery of the Intelligent Key
may not function properly.

— Do not place the Intelligent Key

for an extended period in a
place where temperatures ex-

KEYS

Condition:

(127,1)

[ Edit: 2016/ 2/ 22

Model: 2017MY NISSAN 370Z(Z34) OM17E00Z34U0 ]

ceed 1408F (608C).

— Do not change or modify the

Intelligent Key.

— Do not use a magnet key holder.

— Do not place the Intelligent Key

near an electric appliance such
as a television set, personal
computer or cellular phone.

— Do not allow the Intelligent Key

to come into contact with water
or salt water, and do not wash it
in a washing machine. This
could affect the system function.

.

If an Intelligent Key is lost or stolen,
NISSAN recommends erasing the ID
code of that Intelligent Key. This will
prevent the Intelligent Key from
unauthorized use to unlock the
vehicle. For information regarding
the erasing procedure, it is recom-
mended you visit a NISSAN dealer.

SPA2033

Mechanical key

To remove the mechanical key, release the lock
knob at the back of the Intelligent Key.

To install the mechanical key, firmly insert it into
the Intelligent Key until the lock knob returns to
the lock position.

Use the mechanical key to lock or unlock the
doors, and glove box.

See “Doors” (P.3-4) and “Storage” (P.2-42).

CAUTION

Always carry the mechanical key in-
stalled in the Key.

VALET HAND-OFF

When you have to leave a key with a valet, give
them the Intelligent Key itself and keep the
mechanical key with you to protect your
belongings.

To prevent the glove box from being opened
during valet hand-off, follow the procedures
below.

1. Push the trunk release power cancel switch

to the OFF side (Roadster models).

2. Remove the mechanical key from the In-

telligent Key.

3. Lock the glove box with the mechanical key.

4. Hand the Intelligent Key to the valet, keeping

the mechanical key in your pocket or bag for
insertion into the Intelligent Key when you
retrieve your vehicle.

See “Storage” (P.2-42).

Pre-driving checks and adjustments

3-3

Condition:

(128,1)

[ Edit: 2016/ 2/ 22

Model: 2017MY NISSAN 370Z(Z34) OM17E00Z34U0 ]

3-4

Pre-driving checks and adjustments

WARNING

.

Always have the doors locked while
driving. Along with the use of seat
belts, this provides greater safety in
the event of an accident by helping
to prevent persons from being
thrown from the vehicle. This also
helps keep children and others from
unintentionally opening the doors,
and will help keep out intruders.

.

Before opening any door, always
look for and avoid oncoming traffic.

.

To help avoid risk of injury or death
through unintended operation of
the vehicle and or its systems,
including entrapment in windows
or inadvertent door lock activation,
do not leave children, people who
require the assistance of others or
pets unattended in your vehicle.
Additionally, the temperature inside
a closed vehicle on a warm day can
quickly become high enough to
cause a significant risk of injury or
death to people and pets.

SPA2565

LOCKING WITH MECHANICAL KEY

The power door lock system allows you to lock
or unlock all doors simultaneously using the
mechanical key.

.

Turning the driver’s door key cylinder to the
front of the vehicle

*

1

will lock all doors.

.

Turning the driver’s door key cylinder once
to the rear of the vehicle

*

2

will unlock the

driver’s door. After returning the key to the
neutral position

*

3

, turning it to the rear

again within 60 seconds will unlock all
doors.

.

You can switch the lock system to the mode
that allows you to open all the doors when
the key is turned once. (See “How to use

SETTING button” (P.4-11).)

OPENING AND CLOSING WINDOWS
WITH THE MECHANICAL KEY

The driver’s door key operation also allows you
to open and close the window that is equipped
with the automatic open/close function. (See
“Power windows” (P.2-45).)

To open the window, turn the driver’s door key
cylinder to the rear of the vehicle for longer
than 1 second
. The door is unlocked and the
window keeps opening while turning the key.

This function can also be performed by pushing
and holding the UNLOCK button on the
Intelligent Key. (See “Remote keyless entry
system” (P.3-13).)

To close the window, turn the driver’s door key
cylinder to the front of the vehicle for longer
than 1 second
. The door is locked and the
window keeps closing while turning the key.

DOORS

Condition:

(129,1)

[ Edit: 2016/ 2/ 22

Model: 2017MY NISSAN 370Z(Z34) OM17E00Z34U0 ]

SPA2566

LOCKING WITH INSIDE LOCK KNOB

To lock the door individually, move the inside
lock knob to the lock position

*

1

then close the

door.

To unlock, move the inside lock knob to the
unlock position

*

2

.

When locking the door without an Intelli-
gent Key, be sure not to leave the Intelli-
gent Key inside the vehicle.

SPA2300

LOCKING WITH POWER DOOR LOCK
SWITCH

Operating the power door lock switch will lock
or unlock all the doors and trunk lid. The
switches are located on the driver’s and front
passenger’s door armrests.

To lock the doors and trunk lid, push the power
door lock switch to the lock position

*

1

with the

driver’s or front passenger’s door open, then
close the door and trunk lid.

When locking the door this way, be certain
not to leave the Intelligent Key inside the
vehicle.

To unlock the doors, the fuel-filler door and the

trunk, push the power door lock switch to the
unlock position

*

2

.

Lockout protection

When the power door lock switch (driver or front
passenger) is moved to the lock position with
the Intelligent Key in the port and any door open,
all doors and the trunk lid will lock and unlock
automatically. With the Intelligent Key left in the
vehicle (not in the Intelligent Key port) and any
door open, all doors and the trunk lid will unlock
automatically and a chime will sound after the
door and/or the trunk lid are closed.

These functions help to prevent the Intelligent
Key from being accidentally locked inside the
vehicle.

AUTOMATIC DOOR LOCKS

.

All doors lock automatically when the vehicle
speed reaches 15 MPH (24 km/h).

.

All doors unlock automatically when the
ignition switch is placed in the OFF position.

The automatic unlock function can be
deactivated or activated.
To deactivate or
activate the automatic door unlock system,
perform the following procedure:

1. Close all doors.

2. Place the ignition switch in the ON position.

Pre-driving checks and adjustments

3-5

Condition:

Рассказать друзьям

Страницы