Nissan Primera P12. Instruction - page 97

MULTI-REMOTE CONTROL SYSTEM

BL-97

C

D

E

F

G

H

J

K

L

M

A

B

BL

Remote Controller Battery Check

EIS005HY

1.

CHECK REMOTE CONTROLLER BATTERY

Remove battery and measure voltage across battery positive and negative terminals, (+) and (

).

NOTE:
Remote controller does not function if battery is not set correctly.

OK or NG

OK

>> GO TO 2

NG

>> Replace battery. Refer to

BL-106, "Remote Controller

Battery Replacement"

.

2.

CHECK REMOTE CONTROLLER FUNCTION

With CONSULT-II
Check remote controller function (“RKE LOCK”, “RKE UNLOCK”) in
“DATA MONITOR” mode with CONSULT-II.

OK or NG

OK

>> Remote controller is OK. Further inspection is neces-

sary. Refer to

BL-96, "Trouble Diagnoses"

.

NG

>> Replace remote controller.

The new ID of remote controller cannot be
entered.

1.

Remote controller battery check

BL-97

2.

Key switch check

BL-101

3.

Door switch check

BL-99

4.

Smart entrance control unit power supply and ground circuit
check

BL-98

5.

Replace smart entrance control unit.

Door lock or unlock does not function.

1.

If the power door lock system does not operate manually,
check power door lock system.

BL-25

2.

Remote controller battery check

BL-97

3.

Replace smart entrance control unit.

Hazard reminder does not activate properly
when pressing lock or unlock button of remote
controller.

1.

Remote controller battery check

BL-97

2.

Hazard reminder check

BL-101

3.

Replace smart entrance control unit.

Symptom

Diagnoses/service procedure

Reference

page

( + ) - ( - )

: 2.5V – 3.0V

SEL237W

RKE LOCK

Pushing remote controller lock button

: ON

RKE UNLOCK

Pushing remote controller unlock button

: OFF

SIIA1643E

BL-98

MULTI-REMOTE CONTROL SYSTEM

Smart Entrance Control Unit Power Supply and Ground Circuit Check

EIS005HZ

1.

CHECK POWER SUPPLY CIRCUIT

1.

Turn ignition switch OFF.

2.

Disconnect smart entrance control unit connector.

3.

Check voltage between smart entrance control unit harness connector M43 terminal 49, 56 and ground.

OK or NG

OK

>> GO TO 2.

NG

>> Check the following.

40A fusible link (letter B, located in the fusible link and
fuse box)

10A fuse (No. 12, located in the fusible link and fuse
box)

Condition of circuit breaker-1

Harness for open or short smart entrance control unit power supply circuit.

2.

CHECK GROUND CIRCUIT

Check continuity between smart entrance control unit harness connector M43 terminal 53 and ground.

OK or NG

OK

>> Smart entrance control unit power supply and ground

circuit are OK.

NG

>> Check smart entrance control unit ground circuit for

open or short.

49 (W/L) - Ground

: Battery voltage

56 (R/B) - Ground

: Battery voltage

SIIA1564E

53 (B) - Ground

: Continuity should exist.

SIIA1565E

MULTI-REMOTE CONTROL SYSTEM

BL-99

C

D

E

F

G

H

J

K

L

M

A

B

BL

Door Switch Check

EIS005I0

DRIVER SIDE

1.

CHECK DOOR SWITCH INPUT SIGNAL

WITH CONSULT-II

Check driver door switch signal (“DR DOOR SW”) in “DATA MONITOR” mode with CONSULT-II.

WITHOUT CONSULT-II

1.

Turn ignition switch OFF.

2.

Check voltage between smart entrance control unit harness
connector and ground.

OK or NG

OK

>> Door switch (driver side) is OK.

NG

>> GO TO 2.

2.

CHECK DRIVER SIDE DOOR SWITCH

1.

Disconnect front door switch (driver side) connector.

2.

Check continuity between front door switch (driver side) terminal
1 and ground part of door switch.

OK or NG

OK

>> Check harness for open or short between smart

entrance control unit and front door switch (driver side).

NG

>> Replace front door switch (driver side).

DR DOOR SW

Driver side door is open

: ON

Driver side door is closed

: OFF

MKIB0197E

Connector

Terminal (wire color)

Driver side door

condition

Voltage (V)

(Approx.)

( + )

( - )

M42

43 (R/W)

Ground

Open : (ON)

0

Closed : (OFF)

Battery voltage

MKIB0073E

Terminal

Door switch

Continuity

1

Ground part of
door switch

Pushed

No

Released

Yes

PIIA3351E

BL-100

MULTI-REMOTE CONTROL SYSTEM

EXCEPT DRIVER SIDE

1.

CHECK OTHER DOORS SWITCHES INPUT SIGNAL

WITH CONSULT-II

Check other doors switch signal (“AS DOOR SW”, “RR DOOR SW” or “RR RH DOOR SW”) in “DATA MONI-
TOR” mode with CONSULT-II.

WITHOUT CONSULT-II

Check voltage between smart entrance control unit harness connector and ground.

OK or NG

OK

>> Door switch OK.

NG

>> GO TO 2.

2.

CHECK DOOR SWITCHES

1.

Turn ignition switch OFF.

2.

Disconnect each door switches harness connector.

3.

Check continuity between door switch terminal 1 and ground
part of door switch.

OK or NG

OK

>> Check harness for open or short between smart

entrance control unit and door switch.

NG

>> Replace malfunction door switch.

Each DOOR SW

Each door is open

: ON

Each door is closed

: OFF

MKIB0199E

Item

Connector

Terminal (wire color)

Condition

Voltage (V)

(Approx.)

(+)

(

)

Rear door
LH or RH

M42

39 (BR/W)

Ground

Open

0

Closed

Battery voltage

Passenger
side

44 (L/OR)

Open

0

Closed

Battery voltage

Rear door
LH or RH

45 (R/Y)

Open

0

Closed

Battery voltage

MKIB0583E

Terminal

Condition

Continuity

1

Ground part of

door switch

Pushed

No

Released

Yes

MKIB0584E

Рассказать друзьям