Nissan Primera P12. Instruction - page 61
NAVIGATION SYSTEM
AV-87
C
D
E
F
G
H
I
J
L
M
A
B
AV
2.
HARNESS CHECK
1.
Turn the ignition switch OFF.
2.
Disconnect AV and NAVI control unit connector and Display connector.
3.
Check continuity between AV and NAVI control unit and Display.
4.
Check continuity between AV and NAVI control unit and ground.
●
When the screen looks bluish
●
When the screen looks reddish
●
When the screen looks yellowish
OK or NG
OK
>> GO TO 3.
NG
>>
●
Repair harness.
●
Check connector housings for disconnected or loose terminals.
Terminals
Continuity
(+)
(-)
Connector
Terminal
(wire color)
Connector
Terminal
(wire color)
M54
18 (Y)
M63
1 (Y)
Yes
17
4
Yes
Terminals
Continuity
(+)
(-)
Connector
Terminal (wire color)
M54
17, 18 (Y)
Ground
No
MKIB0639E
Terminals
Continuity
(+)
(-)
Connector
Terminal
(wire color)
Connector
Terminal
(wire color)
M54
21 (W)
M63
2 (W)
Yes
17
4
Yes
Terminals
Continuity
(+)
(-)
Connector
Terminal (wire color)
M54
17, 21 (W)
Ground
No
MKIB0640E
Terminals
Continuity
(+)
(-)
Connector
Terminal
(wire color)
Connector
Terminal
(wire color)
M54
24 (L)
M63
3 (L)
Yes
17
4
Yes
Terminals
Continuity
(+)
(-)
Connector
Terminal (wire color)
M54
17, 24 (L)
Ground
No
MKIB0641E
AV-88
NAVIGATION SYSTEM
3.
RGB SIGNAL CHECK
1.
Connect AV and NAVI control unit connector and Display con-
nector.
2.
Turn the ignition switch ON.
3.
Display “Color bar” by “CONFIRMATION/ADJUSTMENT” mode.
4.
Check voltage signal between AV and NAVI control unit termi-
nals 18, 21, 24 and 17 with oscilloscope or CONSULT-II.
●
When the screen looks bluish
●
When the screen looks reddish
●
When the screen looks yellowish
OK or NG
OK
>> Replace the display unit.
NG
>> Replace AV and NAVI control unit.
MKIB0642E
Terminals
Voltage (v)
(+)
(-)
Connector
Terminal (wire color)
Connector
Terminal
M54
18 (Y)
M54
17
AV-65, "Terminals and Reference Value for AV and
NAVI Control Unit"
Terminals
Voltage (v)
(+)
(-)
Connector
Terminal (wire color)
Connector
Terminal
M54
21 (W)
M54
17
AV-65, "Terminals and Reference Value for AV and
NAVI Control Unit"
Terminals
Voltage (v)
(+)
(-)
Connector
Terminal (wire color)
Connector
Terminal
M54
24 (L)
M54
17
AV-65, "Terminals and Reference Value for AV and
NAVI Control Unit"
NAVIGATION SYSTEM
AV-89
C
D
E
F
G
H
I
J
L
M
A
B
AV
RGB Screen Is Rolling
EKS009K5
1.
HARNESS CHECK
1.
Turn the ignition switch OFF.
2.
Disconnect AV and NAVI control unit connector and Display connector.
3.
Check continuity between AV and NAVI control unit and Display.
4.
Check continuity between AV and NAVI control unit and ground.
OK or NG
OK
>> GO TO 2.
NG
>>
●
Check harness for open or short between AV and NAVI control unit and Display for open or
short circuit.
●
Check connector housings for disconnected or loose terminals.
2.
RGB SYNCHRONIZING SIGNAL CHECK
1.
Connect AV and NAVI control unit connector and Display connector.
2.
Turn the ignition switch ON.
3.
Check voltage between AV and NAVI control unit terminals 15 and 17.
OK or NG
OK
>> Replace the display.
NG
>> Replace AV and NAVI control unit.
Guide Sound Is Not Heard
EKS009K6
1.
CHECK VOICE GUIDE SETTING
●
While driving in the dark pink route, voice guide does not operate.(note)
●
Is volume setting not switched ON?
NOTE:
Voice guide is only available at intersections that satisfy certain conditions (indicated by
●
on the map). There-
fore, guidance may not be given even when the route on the map changes direction.
Yes or No
Yes
>> GO TO 2.
No
>> Switch the setting ON and turn the volume up.
Terminals
Continuity
(+)
(-)
Connector
Terminal
(wire color)
Connector
Terminal
(wire color)
M54
15 (G)
M63
7 (G)
Yes
17
4
Yes
Terminals
Continuity
(+)
(-)
Connector
Terminal (wire color)
M54
17, 15 (G)
Ground
No
MKIB0643E
15 (G)-17
:
Reference Value for AV
and NAVI Control Unit"
MKIB0644E
AV-90
NAVIGATION SYSTEM
2.
HARNESS CHECK
1.
Turn the ignition switch OFF.
2.
Disconnect AV and NAVI control unit connector and Audio unit connector.
3.
Check continuity between AV and NAVI control unit and Audio unit.
4.
Check continuity between AV and NAVI control unit and ground.
OK or NG
OK
>> GO TO 3.
NG
>>
●
Repair harness.
●
Check connector housings for disconnected or loose terminals.
3.
VOICE GUIDE CHECK
1.
Connect AV and NAVI control unit connector and Audio unit connector.
2.
Turn the ignition switch ON.
3.
Check voltage signal between AV and NAVI control unit termi-
nals 8 and 7.
OK or NG
OK
>> Replace Audio unit.
NG
>> Replace AV and NAVI control unit.
Multifunction Switch Controls Are Ineffective (Rear Defogger Control Excluded)
EKS009K7
1.
CHECK POWER AND GROUND SYSTEMS
Check voltage between multifunction switch and ground.
AV-81, "Check Display, Multifunction Switch Power,
and Ground Circuit"
.
OK or NG
OK
>> GO TO 2.
NG
>> Malfunction of multifunction switch ACC power or ground harness
Terminals
Continuity
(+)
(-)
Connector
Terminal
(wire color)
Connector
Terminal
(wire color)
M54
7 (BR)
M53
38 (BR)
Yes
8 (Y)
37 (Y)
Yes
Terminals
Continuity
(+)
(-)
Connector
Terminal (wire color)
M54
7 (BR), 8 (Y)
Ground
No
MKIB0645E
Terminals
Voltage (v)
(+)
(-)
Connector
Terminal
(wire color)
Connector
Terminal
M54
7 (BR)
M54
8 (Y)
AV-65, "Terminals and Ref-
erence Value for AV and
NAVI Control Unit"
MKIB0646E