Defender 300Tdi (1996+). Instruction - page 84

76

CHASSIS AND BODY

20

REPAIR

REAR SEAT BELTS - 90/110 STATION WAGON,
INWARD FACING SEATS

Service repair no - 76.73.18

Remove

1. Release belt straps from buckles.
2. Release stowage straps and lower both seat

cushions.

3. Unscrew bolt securing lap strap to body

mounting.

4. Remove lap strap, wavy washer, spacer and

plain washer.

5. Repeat operation for buckle strap.

Refit

6. Secure lap strap and buckle straps to body.

Tighten bolts to

32 Nm (24 lbf/ft).

7. If required, secure seat cushions and belts in

stowed position.

REAR SEAT BELTS - 110

Service repair no - 76.73.18

Remove

1. Remove rear inward facing seats

See Rear

seat squab - 90 or See Rear bench seat .

2. Remove side trim panel

See Side trim panel .

3. Remove bolt securing seat belt inertia reel to ’C’

post.

4. Remove seat belt assembly.

5. Pull seat belt straps between seat cushion and

squab into rear of vehicle.

6. Remove finisher cap and bolt securing seat belt

anchorage to floor.

7. Remove seat belt assembly.

CHASSIS AND BODY

21

REPAIR

Refit

8. Secure seat belt straps to floor mounting.

Tighten bolt to

32 Nm (24 lbf/ft) and fit finisher

cap.

9. Feed belt straps between seat cushion and

squab.

10. Fit inertia reel to ’C’ post. Tighten bolt to

32 Nm

(24 lbf/ft).

11. Fit side trim panel

See Side trim panel .

12. Fit rear inward facing seats

See Rear seat

squab - 90 or See Rear bench seat .

SIDE TRIM PANEL - 90 STATION WAGON

Service repair no - 76.13.70

Remove

1. Remove rear seat squabs

See Rear seat

squab .

2. Remove rear end trim panel

See Rear end

trim panel .

3. Prise cap from front seat belt upper guide

retaining bolt.

4. Unscrew retaining bolt and remove seat belt

from ’B’ post.

5. Carefully prise trim stud from ’B’ post.
6. Remove 4 bolts securing side trim panel to body

side.

7. Release top edge of side trim panel by striking

upwards with the hand to disengage 3 spring
clips.

8. Lift trim panel from window surround and remove

from vehicle.

76

CHASSIS AND BODY

22

REPAIR

Refit

9. Fit new spring clips to the 3 brackets on top

edge of side trim panel.

10. Align trim panel, ensuring it is correctly

positioned around side window.

11. Locate trim panel spring clips on inner cant rail

and press firmly down to secure top edge of trim
panel.

12. Align bosses of trim panel with body side fixing

holes and secure with 4 bolts and washers. Do
not fully tighten at this stage.

13. Fit trim stud to secure bottom edge of trim panel

to ’B’ post.

14. Secure seat belt guide to ’B’ post, tighten bolt to

32 Nm (24 lbf/ft) and fit cap.

15. Fit rear end trim panel

See Rear end trim

panel .

16. Fit rear seat squab

See Rear seat squab .

SIDE TRIM PANEL - 110 STATION WAGON

Service repair no - 76.13.70

Remove

1. Remove rear inward facing seats

See Rear

seat squab - 90 , or See Rear bench seat .

2. Remove rear end trim panel

See Rear end

trim panel .

3. Prise finisher cap from rear seat belt upper guide

bracket retaining bolt.

4. Unscrew bolt and remove guide bracket from ’C’

post.

5. Remove bolt securing seat belt to wheel arch

mounting.

6. Prise trim panel cap fastener from ’C’ post.
7. Remove seat belt aperture finisher from side trim

panel.

8. Remove screw and release seat belt clip from ’C’

post.

CHASSIS AND BODY

23

REPAIR

9. Remove fixings securing bottom edge of trim

panel to body side.

10. Release top edge of trim panel by striking

upwards with the hand to disengage 3 spring
clips.

11. Lift trim panel from window surround and feed

seat belt through panel aperture.

12. Remove trim panel from vehicle.

Refit

13. Fit new spring clips to the 3 brackets on top

edge of side trim panel.

14. Feed seat belt through aperture in trim panel and

fit finisher.

15. Align trim panel, ensuring it is correctly

positioned around side window.

16. Locate trim panel spring clips on inner cant rail

and press firmly down to secure top edge of trim
panel.

17. Align bosses of trim panel with body side fixing

holes and secure with bolts or screws. If
individual type seats are fitted do not fully tighten
fixings at this stage.

18. Fit seat belt clip to ’C’ post.
19. Fit trim panel cap fastener to ’C’ post.
20. Fit seat belt to wheel arch. Tighten bolt to

32 Nm

(24 lbf/ft).

21. Fit seat belt guide bracket to ’C’ post. Tighten

bolt to

32 Nm (24 lbf/ft) and fit finisher cap.

22. Fit rear end trim panel

See Rear end trim

panel .

23. Fit inward facing seats

See Rear seat squab ,

or

See Rear bench seat .

REAR END TRIM PANEL - 90/110 STATION
WAGON

Service repair no - 76.13.71

Remove

1. Pull edge of rear end trim panel firmly to release

2 spring retaining clips from vertical rail at door
aperture.

2. Remove rear end trim panel.

Refit

3. Fit new spring clips to the 2 brackets on side of

trim panel.

4. Position outboard edge of trim panel in corner to

abut side trim panel and locate spring clips on
vertical rail.

5. Press edge of trim panel firmly to secure in

position.

Рассказать друзьям