Jaguar 5HP24 transmission. Instruction - page 3

Then put measuring bar 5p01 060 330 on
the measuring plate, insert the measuring
base of the dial gauge into the groove of
the measuring plate on the top plate of
the pack and set the dial gauge to zero.

Now measure down to the base plate
using the measuring bar.

Read off the measurement value

M

X

Note!
In each case, index X in M

X

stands

for the clutch pack that was put in for the
clutches/brakes (A, B, C, D, E, F)

1.4/2

98017

98018

Check the value on the force-measuring
unit.

(snap ring)

Determine installation space E

F

for brake

F with measuring bar 5p01 000 330. To
do this, put measuring bar 5p01 000 330
on the edge of the cylinder for brake F.
Put the measuring base on the highest
point of the disc supporting surface on
the piston and set the dial gauge to“0”.
Pull the measuring sensor upwards, guide
it into the snap-ring groove and press it
there against the groove’s upper edge.

Read measured value on the dial ➮ W

F

Determine thickness M

F

of the brake F

clutch pack according to
Chapter 1.4.0: Measuring the clutch pack.

M

F

Installation space E

F

is equal to W

F

plus

the thickness of the base F. ➮ E

F

Test value P

F

is equal to installation

space E

F

minus M

F

The P

F

value must lie between 5.0-6.6 mm.

Setting specification 1055 700 100.

Use test value P

F

to select snap ring S

F

.

Calculation:
E

F

= W

F

+ F

P

F

= E

F

- M

F

Clutch clearance L

F

should be 2.4 -

2.9 mm with 6 lined clutch discs.

1.4/3

98020

98019

1.4.1 Adjusting clearance of brake F

F

= 1.48 mm (base thickness)

W

F

= 32.32 mm

M

F

= 27.82 mm

E

F

= 32.32 + 1.48
= 33.8 mm

P

F

= 33.8 - 27.82
= 5.98 mm

S

F

= 3.4 mm

L

F

= 5.98 - 3.4

L

F

= 2.58 mm

Example (for 1.4.2):

1.4/4

1.4.2 Adjusting clearance of brake D

(snap ring)

Determine installation space E

D

for brake

D with measuring bar 5p01 000 330. To
do this, put measuring bar 5p01 000 330
on the edge of the cylinder for brake D.
Put the measuring base on the highest
point of the disc supporting surface on
the piston and set the dial gauge to“0”.
Pull the measuring sensor upwards, guide
it into the snap-ring groove and press it
there against the groove’s upper edge.

Read measured value on the dial ➮ W

D

Determine thickness M

D

of the brake D

clutch pack according to
Chapter 1.4.0: Measuring the clutch pack.

M

D

Installation space E

D

is equal to W

F

plus

the thickness of the base F. ➮ E

D

Test value P

D

is equal to installation

space E

D

minus M

D

.

The P

D

value must lie between 3.72 - 5.52 mm.

Setting specification 1058 700 067 -

Version

B

Use test value P

D

to select snap ring S

D

.

Calculation:
E

D

= W

D

+ F

P

D

= E

D

- M

D

Clutch clearance L

D

should be 1.35 -

1.65 mm with 4 lined clutch discs.

1.4/5

98022

98021

Рассказать друзьям

Страницы