Engine Iveco C10/C13/C78/Cursor 13/Cursor 78. Instruction - page 1
- < Предыдущая
- Следующая >

The subjects usually dealt with in each section are:
Technical data table, Driving torques, Equipment, Diagnostic, Removal and Fitting in place, Repair operations.
Where possible, the same sequence of procedures has been followed for easy reference.
Diagrams and symbols have been widely used to give a clearer and more immediate illustration of the subject being dealt with, (see
next page) instead of giving descriptions of some operations or procedures.
Example
Ø 1 = housing for connecting rod small end bush
Ø 2 = housing for connecting rod bearings
α
Tighten to torque
Tighten to torque + angular value
1
∅
∅ 2
3
SPECIAL REMARKS

4
Graph and symbols
Removal
Disconnection
Intake
Refitting
Connection
Exhaust
Removal
Disassembly
Operation
Fitting in place
Assembly
ρ
Compression ratio
Tighten to torque
Tolerance
Weight difference
α
Tighten to torque + angle value
Rolling torque
Press or caulk
Replacement
Original spare parts
Regulation
Adjustment
Rotation
!
Warning
Note
Angle
Angular value
Visual inspection
Fitting position check
Preload
Measurement
Value to find
Check
Number of revolutions
Equipment
Temperature
Surface for machining
Machine finish
bar
Pressure
Interference
Strained assembly
Oversized
Higher than
….
Maximum, peak
Thickness
Clearance
Undersized
Less than
….
Minimum
Lubrication
Damp
Grease
Selection
Classes
Oversizing
Sealant
Adhesive
Temperature < 0
°C
Cold
Winter
Air bleeding
Temperature > 0
°C
Hot
Summer

Section
General specifications
1
Fuel
2
Industrial application
3
Overhaul and technical specifications
4
Tools
5
Safety prescriptions
Appendix
PREFACE TO USER’S GUIDELINE MANUAL
Section 1 describes the F2B engine illustrating its features
and working in general.
Section 2 describes the type of fuel feed.
Section 3 relates to the specific duty and is divided in four sepa-
rate parts:
1. Mechanical part, related to the engine overhaul,
limited to those components with different characteristics
based on the relating specific duty.
2. Electrical part, concerning wiring harness, electrical
and electronic equipment with different characteristics
based on the relating specific duty.
3. Maintenance planning and specific overhaul.
4. Troubleshooting part dedicated to the operators who,
being entitled to provide technical assistance, shall have simple
and direct instructions to identify the cause of the major incon-
veniences.
Sections 4 and 5 illustrate the overhaul operations of the engi-
ne overhaul on stand and the necessary equipment to execute
such operations.
Print P2D32C001 E
Base - April 2006

SECTION 1 - GENERAL SPECIFICATIONS
1
SECTION 1
General specifications
Page
CORRESPONDENCE BETWEEN TECHNICAL CODE
AND COMMERCIAL CODE
3
. . . . . . . . . . . . .
VIEWS OF ENGINE (version F2BE0684A*B001
5
.
VIEW OF ENGINE (version F2BE0684A*B002)
8
.
VIEWS OF ENGINE (version F2BE0687A*B101)
9
LUBRICATION
10
. . . . . . . . . . . . . . . . . . . . . . . . . .
- Oil pump
12
. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
- Overpressure valve
12
. . . . . . . . . . . . . . . . . . . . .
- Oil pressure control valve (on the base unit)
13
. .
- Filter support and heat exchanger
13
. . . . . . . . . .
- By-pass valve inside the filter support/heat
exchanger assembly
14
. . . . . . . . . . . . . . . . . . . . .
- Thermostatic valve
14
. . . . . . . . . . . . . . . . . . . . . .
- Engine oil filters
14
. . . . . . . . . . . . . . . . . . . . . . . .
COOLING
15
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
- Description
15
. . . . . . . . . . . . . . . . . . . . . . . . . . . .
- Operation
15
. . . . . . . . . . . . . . . . . . . . . . . . . . . .
- Water pump
17
. . . . . . . . . . . . . . . . . . . . . . . . . .
- Thermostat
17
. . . . . . . . . . . . . . . . . . . . . . . . . . .
TURBOCHARGING
18
. . . . . . . . . . . . . . . . . . . . . .
- HOLSET HX 40W turbocompressor
18
. . . . . . .
- < Предыдущая
- Следующая >