Infiniti FX35 / FX45. Instruction - page 97
AT-316
< SERVICE INFORMATION >
ASSEMBLY
iii.
Tighten adapter case assembly mounting bolts (1) to specified
torque. [With bracket (2).] Refer to
AT-249, "Component"
.
: Bolt (10)
CAUTION:
Do not reuse self-sealing bolts (3).
Refer to GI section to mark sure icons (symbol marks) in the fig-
ure. Refer to
GI-8, "Component"
.
35. Install needle bearing in drum support.
CAUTION:
• Take care with the direction of needle bearing. Refer to
AT-264, "Location of Adjusting Shims, Needle Bearings,
Thrust Washers and Snap Rings"
.
• Apply petroleum jelly to needle bearing.
36. Install direct clutch assembly in reverse brake.
CAUTION:
Make sure that drum support edge surface and direct clutch
inner boss edge surface come to almost same place.
37. Install high and low reverse clutch assembly in direct clutch.
SCIA7210E
SCIA5198E
SCIA5019E
SCIA2306E
ASSEMBLY
AT-317
< SERVICE INFORMATION >
D
E
F
G
H
I
J
K
L
M
A
B
AT
N
O
P
38. Using a flat-bladed screwdriver, align drive plate.
39. Install high and low reverse clutch hub, mid sun gear assembly
and rear sun gear assembly as a unit.
CAUTION:
Check that portion “A” of high and low reverse clutch drum
protrudes approximately 2 mm (0.08 in) beyond portion “B”
of rear sun gear.
40. Install needle bearing in rear carrier assembly.
CAUTION:
• Take care with the direction of needle bearing. Refer to
AT-264, "Location of Adjusting Shims, Needle Bearings,
Thrust Washers and Snap Rings"
.
• Apply petroleum jelly to needle bearing.
SCIA3169E
SCIA5018E
SCIA3130E
SCIA2803E
AT-318
< SERVICE INFORMATION >
ASSEMBLY
41. Install bearing race in rear carrier assembly.
CAUTION:
Apply petroleum jelly to bearing race.
42. Install rear carrier assembly in direct clutch drum.
43. Install needle bearing (rear side) to mid carrier assembly.
CAUTION:
• Take care with the direction of needle bearing. Refer to
AT-264, "Location of Adjusting Shims, Needle Bearings,
Thrust Washers and Snap Rings"
.
• Apply petroleum jelly to needle bearing.
44. Install needle bearing (front side) to mid carrier assembly.
CAUTION:
• Take care with the direction of needle bearing. Refer to
AT-264, "Location of Adjusting Shims, Needle Bearings,
Thrust Washers and Snap Rings"
.
• Apply petroleum jelly to needle bearing.
45. Install mid carrier assembly in rear carrier assembly.
SCIA5175E
SCIA2462E
SCIA2804E
SCIA2805E
SCIA5017E
ASSEMBLY
AT-319
< SERVICE INFORMATION >
D
E
F
G
H
I
J
K
L
M
A
B
AT
N
O
P
46. Install front carrier assembly, input clutch assembly and rear
internal gear as a unit.
47. Install seal rings in input clutch assembly.
CAUTION:
• Do not reuse seal rings.
• Apply petroleum jelly to seal rings.
48. Install band servo anchor end pin and lock nut in transmission
case.
CAUTION:
Do not reuse band servo anchor end pin.
49. Install brake band in transmission case.
CAUTION:
Assemble it so that identification to avoid incorrect installa-
tion faces servo side.
50. Install front sun gear to front carrier assembly.
CAUTION:
Apply ATF to front sun gear bearing and 3rd one-way clutch
end bearing.
SCIA5015E
SCIA2470E
SCIA6512E
SCIA5498E
SCIA5014E