Infiniti FX35 / FX45. Instruction - page 77
AT-236
< SERVICE INFORMATION >
ON-VEHICLE SERVICE
14. Disconnect revolution sensor connector.
CAUTION:
Be careful not to damage connector
15. Straighten terminal clip to free revolution sensor harness.
16. Remove revolution sensor from transmission case.
CAUTION:
• Do not subject it to impact by dropping or hitting it.
• Do not disassemble.
• Do not allow metal filings, etc. to get on the sensor's front
edge magnetic area.
• Do not place in an area affected by magnetism.
INSTALLATION
CAUTION:
After completing installation, check A/T position, A/T fluid leakage and A/F fluid level. Refer to
.
1.
Install revolution sensor in transmission case, and then tighten
revolution sensor mounting bolt to the specified torque. Refer to
"COMPONENTS".
CAUTION:
• Do not subject it to impact by dropping or hitting it.
• Do not disassemble.
• Do not allow metal filings, etc. to get on the sensor's front
edge magnetic area.
• Do not place in an area affected by magnetism.
SCIA7524E
SCIA7525E
SCIA3997E
SCIA3997E
ON-VEHICLE SERVICE
AT-237
< SERVICE INFORMATION >
D
E
F
G
H
I
J
K
L
M
A
B
AT
N
O
P
2.
Connect revolution sensor connector.
3.
Securely fasten revolution sensor harness with clip.
4.
Apply recommended sealant (Genuine Anaerobic Liquid Gasket
or equivalent. Refer to
GI-44, "Recommended Chemical Product
and Sealant"
.) to rear extension assembly as shown in the fig-
ure.
CAUTION:
Completely remove all moisture, oil and old sealant, etc.
from transmission case and rear extension assembly
mounting surfaces.
5.
Install rear extension assembly to transmission case. (With nee-
dle bearing.)
CAUTION:
Insert the tip of parking rod between the parking pole and
the parking actuator support when assembling the rear
extension assembly.
6.
Tighten rear extension assembly mounting bolts to specified
torque. Refer to "COMPONENTS".
CAUTION:
Do not reuse self-sealing bolts.
7.
Install rear engine mounting member. Refer to
AT-241,
"Removal and Installation (2WD Models)"
.
8.
Install oil pan to transmission case.
a.
Install oil pan gasket to oil pan.
CAUTION:
• Do not reuse oil pan gasket.
• Install it in the direction to align hole positions.
SCIA7524E
SCIA7525E
SCIA8228E
SCIA3431E
SCIA6941E
AT-238
< SERVICE INFORMATION >
ON-VEHICLE SERVICE
• Completely remove all moisture, oil and old gasket, etc. from oil pan mounting surface.
b.
Install oil pan (2) (with oil pan gasket) and clips (1) to transmis-
sion case.
•
: Vehicle front
•
: Bolt (22)
CAUTION:
• Install it so that drain plug (3) comes to the position as
shown in the figure.
• Be careful not to pinch harnesses.
• Completely remove all moisture, oil and old gasket, etc.
from oil pan mounting surface.
c.
Tighten oil pan mounting bolts to the specified torque in numeri-
cal order shown in the figure after temporarily tightening them.
Refer to "COMPONENTS".
CAUTION:
Do not reuse oil pan mounting bolts.
9.
Install drain plug to oil pan, and then tighten drain plug to the
specified torque. Refer to "COMPONENTS".
CAUTION:
Do not reuse drain plug gasket.
10. Install control rod. Refer to
AT-206, "Control Rod Removal and
Installation"
.
11. Install rear propeller shaft. Refer to
PR-9, "Removal and Installa-
tion"
.
12. Install exhaust front tube and center muffler. Refer to
EX-3, "Component"
.
13. Install front cross bar. Refer to
FSU-6, "Removal and Installation"
.
14. Pour ATF into A/T assembly. Refer to
AT-11, "Changing A/T Fluid"
.
15. Connect the battery cable to the negative terminal.
SCIA8117E
SCIA4113E
AIR BREATHER HOSE
AT-239
< SERVICE INFORMATION >
D
E
F
G
H
I
J
K
L
M
A
B
AT
N
O
P
AIR BREATHER HOSE
Removal and Installation
INFOID:0000000001327397
VQ35DE ENGINE MODEL
Refer to the figure below for air breather hose removal and installation procedure.
CAUTION:
• When installing an air breather hose, be careful not to be crushed or blocked by folding or bending
the hose.
• When inserting a hose to the transmission tube, be sure to insert it fully until its end reaches the
tube bend R portion.
VK45DE ENGINE MODEL
SCIA2151E