Hummer H1 (2006+). Instruction - page 411
13-18
Accessories
_____________________________________________________________
Figure 13-27: Swing-Away Spare Tire Carrier Breakdown
LOCK
END CAPS
RUBBER
FRAME ASSEMBLY
LANYARD
END
GUIDE
HOLD-DOWN
STOP
ANGLED
BUMPER
SQUARED
SPACER
CUSHION
SIDE
BRACE
SIDE
BRACKET
BLOCK
BRACKET
RETAINING
PLATE
GREASE
FITTING
BRACKET
ASSEMBLY
PIN
CAP
ALUMINUM WHEEL
AND TIRE ASSEMBLY
ADAPTOR
PLATE
TAPERED
LUGNUT
CENTER
CAP
RETAINING
SCREWS
LOCK
NUT
____________________________________________________________
Accessories 13-19
5745804
CARGO BED-MOUNTED SPARE TIRE CARRIER REPLACEMENT
WARNING: Always support the tire and wheel assembly when removing the lug nuts. The tire and wheel assembly
weighs approximately 160 lbs (72 kgs) and may cause personal injury if it is not supported properly.
NOTE: Cargo bed-mounted spare tire carrier may be located either directly behind the cab or at the left wheelhouse on two door
models. On four door models, the spare tire carrier will be located at the left wheelhouse.
Removal
NOTE: Perform steps 1 and 2 on vehicles with frame assembly stowed in the down position.
1.
Disconnect the lock pins and raise the frame assembly to the upright position (Figure 13-28).
Figure 13-28: Cargo Bed-Mounted Spare Tire Carrier Appearance
2.
Secure the frame assembly in the upright position with the lock pins.
3.
Remove the lug nuts securing the tire to the frame assembly and remove the wheel/tire assembly.
4.
Remove the self-tapping screws, lockwashers, and the lanyard/lock pin assemblies from the mounting brackets (Figure
13-29).
5.
Remove the locknuts, bolts and the frame assembly from the mounting brackets.
6.
Remove the screws securing the mounting brackets to the cargo floor (Figure 13-30).
7.
Remove the bolts, lockwashers, washers, and the mounting brackets from the cargo floor.
FRAME ASSEMBLY
WHEEL/TIRE ASSEMBLY
LOCK
PIN
ALUMINUM WHEEL
SPARE TIRE ADAPTER
FLANGED
LUG NUT
6-1-05
13-20
Accessories
_____________________________________________________________
Figure 13-29: Frame Assembly Mounting
Figure 13-30: Mounting Bracket Positioning
Installation
1.
Install the mounting brackets on the cargo floor with the washers, lockwashers, and the bolts (Figure 13-30).
2.
Secure the mounting brackets to the cargo floor with the screws. Tighten the screws to 44 lb-ft (60 N•m).
3.
Install the frame assembly on the mounting brackets with the bolts and the locknuts (Figure 13-29).
4.
Install the lanyard/lock pin assemblies on the mounting brackets and the frame assembly with the lockwashers and the self-
tapping screws.
5.
With the carrier in the upright position, install the tire on the frame assembly with the three lug nuts (Figure 13-28).
NOTE: Perform steps 6 and 7 to stow frame assembly in down position.
6.
Disconnect the lock pins and lower the frame assembly to the down position.
7.
Connect the lock pins.
LANYARD AND
LOCK PIN ASSEMBLY
MOUNTING
BRACKET
FRAME
ASSEMBLY
MOUNTING
BRACKET
CARGO FLOOR
6-1-05
____________________________________________________________
Accessories 13-21
5745804
ALUMINUM WHEEL SPARE TIRE CARRIER ADAPTER
Installation
NOTE: This kit is an accessory for the swing-away spare tire carrier PN 5744642 and the bed mounted spare tire carrier PN
5742944. The swing-away or bed mounted spare tire carrier must be installed before this kit can be used. Refer to the installation
instructions of the swing-away spare tire carrier on page 13–16 or the bed mounted spare tire carrier on page 13–19 .
1.
Install the Aluminum Wheel Spare Tire Carrier Adapter on the mounting flange of the spare tire carrier frame (See Figure
13-31).
2.
Secure the Aluminum Wheel Spare Tire Carrier Adapter using the three 9/16" flanged lug nuts that are supplied with the spare
tire carrier kit.
3.
Install the aluminum spare wheel on the Aluminum Wheel Spare Tire Carrier Adapter securing it with the four supplied
tapered lug nuts.
4.
Place the caution decal on the angled support bar of the tire carrier frame, just below the cushion.
Figure 13-31: Adapter installation.
TIRE AND WHEEL
ASSEMBLY
CENTER
CAP
SPARE TIRE
CARRIER
MOUNTING
ADAPTER
ASSEMBLY
FLANGED
LUGNUTS
LUG
NUT
MOUNTING
FLANGE
CAUTION
DECAL
6-1-05
