Hummer H1 (2006+). Instruction - page 313
10-114 Body
____________________________________________________________________
Figure 10-138: Cargo Door Electric Locks
Door Stop Replacement
Removal
1.
Remove the rear door window.
2.
Remove the four screws and the interior door handle from the door (Figure 10-137).
3.
Remove the twelve screws and the close-out panel from the door.
4.
Remove the bolt, door stop ball and the retainer from the door (Figure 10-139).
5.
Remove the bolt, washer, door stop socket and the retainer from the right rear wheelhouse.
DOOR LOCK MOTOR HARNESS
MOTOR LINK ROD
AND LOCK CLIPS
DOOR HINGE CONTACTS
DOOR
DOOR HINGE CONTACTS
LOCK
MOTOR
___________________________________________________________________
Body 10-115
Figure 10-139: Door Stop and Latch Guide Replacement
Installation
1.
Secure the door stop socket to the right rear wheelhouse with the washer, bolt and the retainer (Figure 10-139).
2.
Secure the door stop ball to the door with the bolt and the retainer.
3.
Secure the close-out panel to the door with the twelve screws (Figure 10-137).
4.
Secure the interior door handle to the close-out panel with the four screws.
5.
Install the rear door window.
Latch Guide Replacement
Removal
Remove the latch guide, two washers and the retaining block from the door frame (Figure 10-139).
Installation
Secure the latch guide to the door frame with the two washers and the retaining block (Figure 10-139).
Adjustment
Close the door and check the alignment, then adjust the latch guide as necessary.
Door Frame and Seal Replacement
Removal
1.
Remove the dome lamp fuse.
2.
Remove the seven screws securing the inner portion of the door hinge to the door frame.
3.
When the hinge is loose, carefully pull away to access the connectors for the door lock contacts in the hinge.
4.
Disconnect the door lock harness connectors and label them for reassembly.
5.
Remove the vertical doors from the door frame.
6.
Remove the upper and the lower latch guides.
7.
Remove the inner passenger side closeout panel on the inside of the door frame.
8.
Disconnect the dome lamp switch harness from the door jamb switch.
9.
Remove the fourteen screws from the door frame (Figure 10-140).
10. Remove the door frame completely
DOOR
STOP
BALL
DOOR STOP
SOCKET
RETAINER
LATCH
RETAINING
BLOCK
GUIDE
10-116 Body
____________________________________________________________________
11. Remove the seal from the door frame.
Figure 10-140: Door Frame and Seal Replacement
Installation
1.
Position the seal on the door frame (Figure 10-140).
2.
Secure the door frame to the vehicle with the fourteen screws.
3.
Install a new door jamb switch and connect it to the dome lamp harness.
4.
Install the upper and the lower latch guides.
5.
Install the vertical doors on the door frame.
6.
Connect the door lock harness connections to the back of the door hinge contacts.
7.
Install the interior closeout panel.
8.
Close the door to adjust the new door jamb switch.
9.
Install the dome lamp fuse.
10. Verify the operation of the door lamps and the cargo switch.
INTERIOR AND EXTERIOR LIGHTING REPLACEMENT
Service Headlight Assembly Replacement
Removal
NOTE: To remove the headlight only, perform steps 1 and 2. To remove the entire assembly, continue with steps 3 through 6.
1.
Loosen the three screws and remove the retaining ring from the headlight mount (Figure 10-141).
2.
Disconnect the headlight jumper harness from the headlight and the remove headlight.
3.
Loosen the two screws securing the headlight mount to the headlight housing and remove the mount from the housing and the
spring.
4.
Disconnect the headlight jumper harness from the headlight housing and remove the harness.
5.
Disconnect the three leads from the back of the housing.
6.
Remove the three nuts, lockwashers, washers and the housing from the hood.
Installation
NOTE: To install the headlight only, perform steps 5 and 6. To install the entire assembly, perform all the steps.
1.
Connect the three leads to the back of the housing (Figure 10-141).
DOOR
FRAME
SEAL
___________________________________________________________________
Body 10-117
2.
Secure the headlight housing to the hood with the three washers, lockwashers and the nuts.
3.
Secure the headlight mount to the housing, with the spring and the two screws.
4.
Connect the headlight jumper harness to the headlight housing.
5.
Connect the headlight to the jumper harness and secure the headlight to the headlight mount with the retaining ring and the
three screws.
6.
Check the headlight for proper operation.
Figure 10-141: Headlight Assembly Replacement
Side Marker Light Lens and Lamp Replacement
Removal
1.
Remove the two retaining screws and pull the side marker light away from the body until the harness is exposed. (Figure
10-142).
2.
Disconnect the harness and remove the side marker light.
3.
Remove the bezel and the gasket.
Installation
1.
Feed the side marker light through the gasket and the bezel.(Figure 10-142).
2.
Connect the side marker light harness to the underbody harness.
3.
Align the side marker light, gasket and the bezel with the mounting holes on the body and secure with the retaining screws.
4.
Ensure the side marker light operates properly.
Figure 10-142: Side Marker Light Lens and Lamp Replacement
RETAINING RING
HEADLIGHT
HEADLIGHT MOUNT
JUMPER HARNESS
SPRING
HEADLIGHT HOUSING
LEADS
HOOD
GASKET
SIDE MARKER
LIGHT
SCREW
BEZEL
