Hummer H1 (1992-1998). Instruction - page 61
- < Предыдущая
- Следующая >
APPENDIX E
TOOL IDENTIFICATION LIST
Section I. INTRODUCTION
E-1. SCOPE
This appendix lists common tools, special tools, and test equipment needed to maintain the 6.2L and 6.5L
diesel engines.
a. Column (1) - Item Number.
This number is assigned to each entry in the listing and is referenced in
the “Initial Setup” of applicable tasks under the headings of “Test Equipment,” Tools,” and “Special Tools.”
b. Column (2) - Item Name.
Name or identification of the tool or test equipment.
c. Column (3) - National Stock Number. The
national stock number of the tool or test equipment.
d. Column (4) - Part Number.
The manufacturer’s part number.
e. Column (5) - Reference.
This column lists the references used to identify and illustrate the tools
and test equipment needed for maintaining the 6.2L and 6.5L diesel engines.
Section II. TOOL IDENTIFICATION LIST
(1)
(2)
(3)
(4)
(5)
National
Stock
Number
Item Name
Number
Part Number
Reference
1
Tool kit, general mechanic’s
5180-00-177-7033
SC 5180-90-CL-N26
automotive
2
Engine repair stand
4910-00-506-0037
1725A
3
Engine lifting sling
4910-01-193-7808
J33139
4
Hydraulic valve lifter remover
5120-01-209-6870
J29834
TM 9-2815-234-34P
5
Injection nozzle socket
5120-01-171-5233
J29873
6
Glow plug socket
5120-00-277-1463
FUS121
7
Hex head driver, 6 mm
5120-01-055-1308
FAM6
8
Hex head driver, 8 mm
5120-01-053-4159
FAM8
9
Hex head driver, 5/16 in.
5120-00-683-8602
FA10B
10
Dial indicator
5210-00-277-8840
SC 4910-95-CL-A02
11
Cylinder ridge reamer
5110-00-237-8598
SC 4910-95-CL-A02
12
Camshaft bearing remover
5120-01-206-3818
J35178
and installer
13
Feeler gauge
5210-01-045-3526
SC 4910-95-CL-A31
14
Cylinder bore gauge
5210-00-494-1774
SC 4910-95-A63
15
Straightedge
6675-00-224-8807
SC 4910-95-A63
16
Micrometer
5210-00-5547134
SC 4910-95-A63
17
Cylinder boring machine
4910-00-473-6361
SC 4910-95-A63
18
Cylinder honing unit
5130-00-991-0699
SC 491 0-95-A63
19
Puller
5120-00-595-9305
SC 4910-95-CL-A31
20
Piston ring expander
5120-00-857-3190
SC 4910-95-CL-A31
21
"V" blocks
3460-00-725-5076
SC 4910-95-CL-A02
22
Valve spring compressor
5120-00-239-8686
SC 4910-95-A63
23
Bench grinder
3415-00-517-7744
SC 4910-95-CL-A31
24
Rotary wheel wire brush
5130-00-473-6444
SC 4910-95-CL-A31
25
Electric drill
5130-00-889-8993
SC 4910-95-CL-A31
26
Rotary end wire brush
5130-00-293-2409
SC 4910-95-CL-A31
27
Valve spring tester
6635-00-641-7346
SC 4910-95-A63
28
Valve face grinding machine
4910-00-540-4679
SC 4910-95-A63
29
Valve seat grinding kit
4910-00-473-6437
SC 4910-95-A63
E-2
Change 1 E-3
Section II. TOOL IDENTIFICATION LIST (Cont’d)
(1)
(2)
(3)
(4)
(5)
National
Item
Stock
Number
Item Name
Number
Part Number
Reference
30
Hammer, soft-head
5120-01-071-5356
SC 4910-95-A62
31
Injection nozzle tester
4910-00-255-8641
SC 4910-95-CL-A01
32
Multimeter
6625-01-139-2512
AN/PSM-45
SC 4910-95-CL-A74
33
Rear main seal installer (6.2L)
5120-01-210-8792
J33153
34
Rear main seal installer (6.5L)
5120-01-422-0334
J39084
35
Piston ring compressor
5120-00-250-6055
SC 4910-95-CL-A02
36
Crowfoot, 16 mm
5120-01-242-8165
J35159
37
Crowfoot, 19 mm
5120-01-230-9421
J35160
38
Fuel injection nozzle, remover
5120-01-171-5233
J29873
39
Drive shaft bearing, installer
5120-01-208-7771
23805
40
Drive shaft seal, installer
5120-01-208-7752
22727
41
Throttle and shutoff shaft
5120-01-189-0448
18411
bushing kit
42
Torx drive, T27, socket
5120-01-078-1899
22939
43
Governor weight support
5120-01-197-0236
16313
44
End cap wrench
5120-01-207-5563
20548
45
Roller-to-roller setting tool
5120-01-200-4526
19969
46
Holding fixture
5120-01-208-7753
23615
47
Pilot tube mandrel
5120-01-208-1767
16314
48
Delivery valve, extractor
5120-00-816-7059
26081
test set, calibration
49
Linkage gap tool
5120-01-249-0370
23080
50
Automatic advance indicator
5120-01-249-0368
23745
51
Vacuum valve block gauge
5120-01-249-0369
23716
52
Protractor
6675-01-247-2286
22089
53
Air timing gauge
5220-01-247-0361
23715
54
Hex-head driver, 5/32 in.
5120-00-969-0071
J35170
55
Hex-head driver, 1/8 in.
5120-01-016-9202
J35171
56
Hex-head driver, 1/4 in.
5120-00-596-8508
FA8A
57
Adapter plate
67-6878
Kit 74-8033
58
Advance indicator
74-1094
Kit 74-8033
E-4 Change 1
Section II. TOOL IDENTIFICATION LIST (Cont’d)
(1)
(2)
(3)
(4)
(5)
National
Item
Stock
Number
Item Name
Number
Part Number
Reference
59
Alignment gauge
4910-01-397-1616
67-4787
Kit 74-8033
60
Barring tool
4910-01-211-0879
67-2840
Kit 74-8033
61
Connector
67-5687
Kit 74-8033
62
High-pressure line
74-1250
Kit 74-8033
63
Hose assembly
74-1337
Kit 74-8033
64
Hose assembly
74-1030
Kit 74-8033
65
Male pipe fitting
03-5253
Kit 74-8033
66
Quick-connect plug
67-3456
Kit 74-8033
67
Test adapter
74-1131
Kit 74-8033
68
Test lead, black
Kit 74-8033
69
Test lead, red
77-0432
Kit 74-8033
70
Throttle arm
67-5649
Kit 74-8033
positioner assembly
71
Tubing
4720-01-206-4429
03-6063
Kit 74-8033
- < Предыдущая
- Следующая >