Geely FC. Manual part - 49
Geely FC. Manual part - 49
Steering column--Steering system
Steering column--Steering system
Steering column--Steering system
Steering column--Steering system
Steering column--Steering system
Inspection on automobile
1. Check the free clearance of steering wheel
(a) Park the automobile, and the front wheels are towards the
front.
(b)Turn the steering wheel to left and right with your fingers
lightly, and check the free clearance.
Maximal free clearance: 30mm
Maximal free
clearance
193
Steering column system
Overhaul
1. Put the front wheels towards the front.
2. Disassemble safety airbag assembly at the side of
driver (equipping with SRS) [67000179]
Note: if disconnecting airbag joint when ignition switch
locates at ON position, checking number will record it.
(a) Put the front wheels towards the front.
(b) Use planetary sleeve wrench to loosen two planetary
screws until the concave slot around the screw contacts
the screw shell.
(c) Pull out airbag assemble from steering wheel, and
disassemble airbag joint.
(d) Disassemble the terminal.
Warning:
¡ñ
¡ñ
¡ñ
¡ñ
¡ñ
When storing safety airbag assembly at the side
of driver, it is necessary to put the surface of
airbag assembly towards the upside.
¡ñ
¡ñ
¡ñ
¡ñ
¡ñ
Do not disassemble airbag assembly.
Note: when disassembling airbag assembly, pay
attention not to pull airbag wiring harness.
3. Disassemble steering wheel assembly [67100001]
(a) Disassemble the fixed screw cap of steering wheel.
(b) Make corresponding marks on steering wheel and main
shaft assembly.
(c) Use special tool to disassemble steering wheel.
4. Disassemble upper/lower decoration plate of
steering column [64000128/64000129]
5. Disassemble left combination switch assembly
[67000078] (referring to page 298)
Steering column--Steering system
Steering column--Steering system
Steering column--Steering system
Steering column--Steering system
Steering column--Steering system
airbag joint
Correct
Wrong
planetary
screws
screw shell
194
Align the mark
Steering column--Steering system
Steering column--Steering system
Steering column--Steering system
Steering column--Steering system
Steering column--Steering system
6. Disassemble right combination switch assembly
[67000079] (referring to page 302)
7. Disassemble helix cable assembly (equipping with
SRS)
Note: do not disassemble helix cable or spread lubricat-
ing grease.
8. Disassemble the middle connecting plate of lower
panel [68100006] (referring to page 340)
9. Disassemble dust-proof cover in steering column.
Disassemble two screw caps, then take down dust-proof cover
in steering column.
10. Disassemble steering shaft assembly
(a) Disconnect joint and fixed clap of wiring harness.
(b) Loosen three fixed bolts of steering column assembly.
11. Disassemble the clamp of ignition switch [68000020]
(a) Use central punch to make hole on the central part be-
tween two tapered bolts.
(b) Use 3-4 mm aiguille to drill two bolts.
(c) Use bolt screwdriver to disassemble two bolts, then take
down ignition switch clamp.
12. Disassemble electronic anti-stealing loop assem-
bly (assembling with enter illumination system)
[67000009].
195
Bolt screwer
Steering column--Steering system
Steering column--Steering system
Steering column--Steering system
Steering column--Steering system
Steering column--Steering system
13. Disassemble ignition switch key tank assembly
(a) Put ignition switch key tank on ACC position.
(b) Pull down stop pin and pull out key tank assembly with
right-angled screwdriver.
14. Disassemble ignition switch assembly
Disassemble two screws, and take down ignition switch
assembly.
15. Assemble ignition switch with locking core and key
assembly [68000019]
Assemble ignition switch with locking core and key assembly
with two screws.
16. Assemble ignition switch key tank assembly
(a) Make sure ignition switch key tank assembly locates at
ACC position.
(b) Assemble ignition switch key tank.
17. Steering locking function
(a) When taking out the key, check whether steering locking
organization is locked.
(b) When inserting the key, and turning to ACC, check whether
the steering locking organization is released.
18. Assemble electronic anti-stealing loop assembly
[67000009]
19. Assemble ignition switch clamp [68000020]
20. Assemble steering shaft assembly
(a) Assemble steering column assembly with three bolts.
Torque: 21 ± 2 N
xm
196