Geely FC. Manual part - 39

Geely FC. Manual part - 39

Brake--Speed sensor of rear wheels

153

(c) Use special tool and press to assemble speed sensor of

rear wheels to rear shaft hub.

Note:

z

Do not use hammer knock directly in speed sensor

of rear wheels.

z

Insure no sundries are attached on the supervising

part of speed sensor of rear wheels

z

Press speed sensor of rear wheels straightly and

slowly.

8. Assemble left rear shaft hub and bearing assembly

(referring to page 129).

9. Assemble brake disk.

10. Assemble left rear brake branch pump.

11. Assemble wiring harness of speed sensor of rear

wheels.

12. Assemble rear wheels.

Torque: 103

±±±±± 10 N⋅⋅⋅⋅⋅m

13. Check and adjust wheel alignment.

14. Check the signal of ABS speed sensor.

Special

tool

Parking brake

Parking brake system

Malfunction phenomenon table

Use following table to find the reason of malfunction, the number in table indicates the preferred se-

quence of possible reason. Please check each part by sequence, if necessary, change this part.

Parking brake--Parking brake system

Adjustment

1. Disassemble rear wheels

2. Adjust the clearance of parking brake shoe

3. Assemble rear wheels

Torque: 103

±±±±± 10 N⋅⋅⋅⋅⋅m

4. Check the travel of parking brake handle.

Pull up the parking brake handle and calculate the sound num-

ber of handle.

When parking brake handle locates 196N: 6-9 sounds.

5. Adjust the travel of parking brake handle

(a) Disassemble upper trim board of central box.

(b) Disassemble central box.

(c) Release locking screw cap, then rotate adjusting screw cap

until handle travel accords with the specification.

(d) Tighten locking screw cap.

Torque: 5.0 N

⋅⋅⋅⋅⋅m

(e) Assemble central box.

(f) Assemble trim board on central box.

Malfunction phenomenon

Possible malfunction part

Reference page

1. Travel of parking brake handle (adjusted badly).

154

2. Pull cable of parking brake (attached).

156, 158

Brake lag

3. Clearance of parking brake shoe (adjusted badly).

161

4. Friction plate of parking brake shoe (damaged or distorted).

161

5. Tension or return spring (damaged).

161

Lock the screw cap

Adjust the
screw cap

154

Parking brake handle assembly

Change

1. Disassemble trim board on central box.

2. Disassemble parking brake hole cover.

3. Disassemble central box.

4. Disassemble parking brake handle assembly.

(a) Disassemble locking screw cap and adjusting screw cap.

(b) Disassemble the joint of parking brake switch.

(c) Disassemble two bolts and parking brake handle.

5. Disassemble parking brake switch assembly.

Disassemble the screw and parking brake switch.

6. Assemble parking brake switch assembly.

Assemble parking brake switch assembly with screw.

7. Assemble parking brake pull cable.

(a) Connect parking brake pull cable to handle and assemble adjusting screw cap and locking screw cap.

(b) Assemble parking brake handle with two bolts.

Torque: 13 N

⋅⋅⋅⋅⋅m

(c) Connect the joint of parking brake switch.

8. Check the travel of parking brake handle (referring to page 154).

9. Adjust the travel of parking brake handle (referring to page 154).

Parking brake--Parking brake handle assembly

155

Parking front brake pull cable assembly

Change

Parking brake--Parking front bake pull cable assembly

156

1. Disassemble upper trim board on box.

2. Disassemble parking brake hole cover.

3. Disassemble central box.

4. Disassemble parking brake handle assembly.

5. Disassemble front bottom board bracket.

6. Disassemble front exhaust pipe with Three-Way

Catalytic Converter assembly.

(a) Disassemble the joint of oxygen sensor.

(b) Disassemble four bolts, compressed spring and front ex-

haust pipe with Three-Way Catalytic Converter assembly.

7. Disassemble heat insulation board of front exhaust

pipe.

Disassemble there screw caps and heat insulation board of

front exhaust pipe.

8. Disassemble parking front brake pull cable

assembly.

9. Assemble parking front brake pull cable assembly.

10. Assemble heat insulation board of front exhaust

pipe.

Assemble heat insulation board of front exhaust pipe with there

screw caps.

Torque: 5.4 N

⋅⋅⋅⋅⋅m

11. Assemble front exhaust pipe with Three-Way Cata-

lytic Converter assembly.

(a) Assemble two new gaskets and front exhaust pipe with

Three-Way Catalytic Converter assembly with four com-

pressed springs and bolts.

Torque: 43

±±±±± 3 N⋅⋅⋅⋅⋅m

(b) Connect the joint of oxygen sensor.

Рассказать друзьям