Geely FC. Manual part - 33
Geely FC. Manual part - 33
Drive shaft--Left rear shaft hub and bearing assembly
Left rear shaft hub and bearing assembly
Change
Hint: changing procedure for right side is same as left side.
129
6. Disassemble rear wheel speed sensor assembly (equipping with ABS) [67000023]
(referring to page 52)
7. Assemble rear wheel speed sensor assembly (equipping with ABS) [67000023] (referring
to page 52)
1. Disassemble rear wheels.
2. Disassemble rear brake caliper assemble
Disassemble two bolts and take down brake caliper.
3. Disassemble the wiring harness of rear wheel speed
sensor (equipping with ABS).
Disassemble the joint of rear wheel speed sensor.
4. Disassemble left rear brake assembly [64000137]
5. Disassemble left rear shaft hub and bearing
assembly.
Disassemble four bolts, then take down lower shaft hub and
bearing assembly.
8. Assemble left rear shaft hub and bearing assembly
Use four bolts to assemble left rear shaft hub and bearing
assembly
9. Assemble wiring harness of rear wheel speed sen-
sor (equipping with ABS).
Connect the joint of rear wheel speed sensor.
10. Check the axial clearance of bearing.
Put the centimeter besides shaft hub center, and check the
axial clearance of bearing.
Maximal value: 0.05mm
If axial clearance exceeds the maximal value, change the bearing
assembly.
11. Check the terminal face run-out of shaft hub.
Use centimeter to check the terminal run-out of exterior sur-
face of shaft hub.
Maximal value: 0.07m
If terminal run-out exceeds the maximal value, change the shaft
hub.
12. Assemble left rear brake assembly [64000137]
13. Assemble left rear brake branch pump assembly
Torque: 46 ± 5 N
⋅⋅⋅⋅⋅m
14. Assemble rear wheels
Torque: 103 ± 10 N
⋅⋅⋅⋅⋅m
15. Check the ABS speed sensor signal.
16. Inspection on road.
Drive shaft--Left rear shaft hub and bearing assembly
130
Left rear shaft hub bolt
Change
1. Disassemble rear wheels
2. Disassemble left rear brake caliper assemble
Disassemble two bolts and take down brake caliper.
3. Disassemble left rear brake assembly [64000137]
4. Disassemble left rear shaft hub bolt
(a) Screw the shaft to the position in figure, then use special
tool to disassemble shaft hub bolt.
Note: shaft hub bolt should be screwed to the position
in figure, or you could not change shaft hub bolt.
(b) Use special tool and screw driver to disassemble shaft hub
bolt.
5. Assemble left rear shaft hub bolt
(a) Liking that shown in figure, assemble new gasket and screw
cap on new shaft hub bolt.
(b) Use screw driver to fix and lock screw cap to make the bolt
enter hole.
6. Assemble left rear brake assembly [64000137]
7. Assemble left rear brake branch pump assembly
Use two bolts to assemble rear brake branch pump assembly.
Torque: 46 ± 5 N
⋅⋅⋅⋅⋅m
8. Assemble rear wheels
Torque: 103 ± 10 N
⋅⋅⋅⋅⋅m
Drive shaft--Left rear shaft hub bolt
131
Brake--Brake system
Brake
Brake system
Notes
z
It is necessary to be very careful when changing any subassembly, for this will influence the perfor-
mance of brake system and incur the running becomes unsafe. It is necessary to use those parts with
same type or same grade when changing.
z
When repairing brake system, it is very important to keep the surface of every part clean.
132