Geely CK (2008). Manual part - 48
Geely CK (2008). Manual part - 48
189
II. SPEEDOMETER INSPECTION
1. INSPECT THE INDICATING ERROR ALLOWED BY SPEEDOMETER USING A SPEEDOM-
ETER TESTER, AND INSPECT THE OPERATION OF THE ODOMETER.
NOTICE:
Tire over or under inflation will cause the reading error.
2. INSPECT INPUT SIGNAL
(a) Connect the positive (+) pole of the voltmeter to terminal A-11, and the negative (-) to the terminal A-9.
(b) When the vehicle runs at 10 Km/h, inspect the voltage between terminal A-11 and A-9 of the combination
meter.
Standard: 7 wave forms of the high-low electrical level change per second.
NOTICE:
Hold the ignition switch ON when inspected, connect the connector.
3. INSPECT TACHOMETER
Inspect its operation
(1) Start the engine, using a handy tachometer to compare.
(2) The value displayed on the handy tachometer and the value indicated on the tachometer are as follows.
Meter indication
Value displayed on the tester
20
17—23
40
35—40
60
55—60
80
75—80
100
95—100
120
114—120
140
133—140
160
152—160
180
171—180
Analog Meter (Km/h)
190
Analog Meter
4. INSPECT FUEL LEVEL GAUGE
(1) Inspect resistance
When the fuel level gauge indicates no fuel, inspect the resistance between terminal A-12 and B-7 on the
combination meter connector.
Standard:
NOTICE:
Connector should be disconnected when measured.
5. INSPECT WATER TEMPERATURE GAUGE
(1) Inspect resistance
When the water temperature is indicated in the red area, inspect the resistance between terminal B-5 and
B-7 on the combination meter connector.
Tachometer (r/min)
handy tachometer (r/min)
800
740—860
1000
900—1100
2000
1850—2150
3000
2800—3200
4000
3800—4200
5000
4800—5200
6000
5750—6250
Standard indication
Resistance (Ω)
E
104—116
Warning point
90—100
1/2F
29—35
F
1—5
191
Standard
NOTICE:
Connector should be disconnected when measured.
6. INSPECT WATER TEMPERATURE WARNINGLIGHT
(a) Disconnect the water temperature sensor connector.
(b) Turn the ignition ON, the water temperature warning light should go out.
(c) Ground the terminal B5 of the meter connector, the water temperature warning light should light up.
7. INSPECT OIL PRESSURE WARNING LIGHT
(1) Disconnect the oil pressure sensor connector.
(2) Turn the ignition ON, the oil pressure warning light should go out.
(3) Short connector terminal to the ground with a wire, the oil pressure warning light should light up.
8. INSPECT OIL PRESSURE SENSOR
(1) Disconnect the connector from the oil pressure sensor .
(2) Inspect continuity between its terminal and ground.
Engine is stopped: Continuity
Engine runs: No continuity
9. INSPECT PARK BRAKE WARING LIGHT
(1) Disconnect the connector from the park brake switch.
(2) Turn the ignition ON, the park brake warning light should go out.
(3) Short connector terminal to the ground with a wire, the park brake warning light should light up.
Standard indication
Resistance (Ω)
C
159.5—169.5
1/2H
53—59
Warning point
26.7—30.7
H
20—24
192
10. INSPECT PARK BRAKE SWITCH
(1) Disconnect the connector from the park brake switch.
(2) Pull up the hand brake, inspect continuity between its terminal and ground.
Hand brake is pulled up: Continuity
Hand brake is released: No continuity
11. INSPECT BRAKE FLUID LEVEL WARING LIGHT
(1) Disconnect the connector from the brake fluid level sensor.
(2) Turn the ignition ON, the brake fluid level warning light should go out.
(3) Directly connect its connector terminal to the harness terminal with a wire, the brake fluid level warning
light should light up.
12. INSPECT BRAKE FLUID LEVEL WARING SWITCH
(1) Remove the reservoir cap
(2) Disconnect the connector from the reservoir.
(3) Inspect continuity between terminals
Float up: No continuity
(4) Use siphon to take fluid out of the reservoir.
(5) Inspect continuity between terminals
Float down: Continuity
(6) Pour the fluid into the reservoir
13. INSPECT THE REAR DEFROST INDICATOR
(1) Turn the ignition switch ON, and start the engine
(2) Press the defrost switch, the rear defrost indicator will light up
(3) Turn the ignition OFF, the rear defrost indicator should go out.
14. INSPECT THE REAR DEFOG INDICATOR
(1) The rear fog indicator will light up as the rear fog lamp lights, the terminal B1 is at the high electric
potential.
15. INSPECT THE SEAT BELT WARNING INDICATOR
(1) Disconnect the seat belt switch connector in the driver's side, the belt warning indicator should go out at
this time.
(2) Short connector terminal to the ground, the belt warning indicator should light up.