Geely CK (2008). Manual part - 32

Geely CK (2008). Manual part - 32

125

Section 8 No. 2 Transverse Arm Assembly

Components

Replacement

1. Remove the strut rod mount component

Remove the strut rod mount component bolt on the No. 2 transverse arm assembly

2. Remove transverse arm assembly No. 2

(1) Remove the bolt connecting the No. 2 transverse arm assembly and rear brake assembly

(2) Remove the bolt connecting the No. 2 transverse arm assembly and vehicle body, rear wheel toe-in

adjust plate and rear wheel toe-adjust cam

3. Install No. 2 transverse arm assembly

(1) Use the nut, rear wheel toe-in adjust cam, rear wheel toe-in adjust plate to attach the No. 2 transverse

arm assembly to the body

(2) Install the No. 2 transverse arm assembly to the rear brake wheel hub. Torque : 81~96N.m

(3) Use the bolt to attach the strut rod component to the No. 2 transverse arm assembly. Torque :

22~25N.m

4. Check the rear wheel alignment, adjust it by adjusting the rear wheel toe-in adjust cam and adjust plate.

After the adjustment, tighten the bolts to torque 45~55N.m

Rear Stabilizer Bar
Strut Rod Component

Pivot Bracket

Body
Bottom Plate

No. 2 Transverse Arm
Welding Component

No. 2 Transverse Arm Bushing

Rear Wheel Toe-in Adjust Plate

Rear Wheel Toe-in
Adjust Cam

126

Chapter 7 Wheel

Section 1 Tire Inspection

Inspection

1. Check the tires for appearance and proper inflation pressure.

Check for inflation pressure after the vehicle stops for over 15min.

2. Using a dial gauge, check the runout of tire.

The tire runout should be no more than 3.0mm

Notice

(1) You must use specified tire and special wheel rim provided by the authorized service

center, otherwise it may affect the normal safe running of the vehicle and even result in

accidents!

(2) If the wheel rim is damaged, you must go to the authorized service center for service and

replacement! Never use the wheel rim of any other model!

3. Changing tire position

It is recommended to change the tire for each 10000km driving. See the figure for where to change each

tire

4. Inspect wheel dynamic balance

The imbalance should be no more than 8.0g. Otherwise, there will be extra vibration and noise when

driving.

Tire module

Tire inflation

pressure(Kpa)

175/65 R14 82H

220

Front

127

Section 2 Wheel Replacement

Replacement

(1) Pry the edge of the wheel rim trim cover with screwdriver to remove the wheel rim trim cover

(2) Loose every tire nut with tire nut wrench.

(3) Four jacks support the vehicle body, two at each side as shown in the figure.

The jack should be near to the to-be-replaced wheel with solid base.

(4) Remove the wheel nut.

Caution:

(1) Make sure the parking brake control handle has been pulled up before jacking up the

vehicle

(2) Wheel nut torque : 95~115N.m

(3) Check the four wheel alignment when necessary

128

Chapter 8 Power Steering System

Section 1 Power Steering System

Power Steering System Description

Power Steering System consists of the steering wheel, steering transmit device, power steering fixed device

and steering pipelines. The steering gear is rack and pinion type.

Major parameters for steering system:

Cautions:

1. Cautions for steering system

Make sure of the correct replacement of parts, incorrect replacement might affect the performance of

the steering system and lead to driving accidents.

2. Cautions for SRS System

This vehicle is equipped with SRS (Supplemental Restraint System), driver side air bag and front passenger

side air bag.

Failure to carry out service operations in the correct sequence could cause the unexpected deployment of

the air bag during servicing, possibly leading to a serious accident.

Parameter

3.26

Inner 37.6°

Outer 33.3°

≤ 10.5m

Item

Steering Wheel total revolutions

Maximum Front

Wheel Turn Angle

Minimum Turning Diameter

Рассказать друзьям