Fiat 124 Spider Abarth (2017 year). Instruction - page 12
Replacement Bulbs
Light bulbs
Type
Power
Front position
LED
–
Front side-maker lights (if equipped with Full-LED headlights)
W5W
5 W
Front positions/side-maker lights (if equipped with halogen headlights)
WY5W
5 W
High beam (if equipped with Full-LED headlights)
LED
–
High beam/Daytime Running Lights (DRL) (if equipped with halogen headlights)
HB3
60 W
Daytime Running Lights (DRL) (if equipped with Full-LED headlights)
LED
–
Low beam (if equipped with Full-LED headlights)
LED
–
Low beam (if equipped with halogen headlights)
H11
55 W
Front Direction indicator light
WY21W
21W
Side direction indicator light
WY5W
5 W
Fog light
H11
55 W
Rear position Lights
LED
–
Stop lights
LED
–
Center High Mount Stop Lamp (CHMSL)
LED
–
Rear direction indicator light
WY21W
21 W
Rear Side marker
W5W
5 W
Reverse light
W21W
21 W
License plate light
W5W
5 W
Overhead Light
10 W
Trunk Lid Light
5 W
185
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Light Bulbs
Front Lights
The bulbs are arranged as follows :
Rear Lights
The bulbs are arranged as follows :
Replacing Exterior
Lights
Headlights (low beam)
(If Equipped with halogen bulb)
Proceed as follows:
1. If you are changing the right bulb,
start the engine, turn the steering wheel
all the way to the right, and turn off
engine. If you are changing the left bulb,
turn the steering wheel to the left.
2. Make sure the ignition is placed in
the OFF mode, and the headlight
switch is off.
3. Remove the fasteners in the seven
locations and partially peel back the
mud guard
4. Turn the cover counterclockwise and
remove it, disconnect the connector
from the unit by pressing the tab on the
connector with your finger and pulling
the connector.
5. Turn the socket and bulb assembly
counterclockwise and remove it.
6. Disconnect the bulb from the
socket.
04110102-L38-008
Head Lights
1 — High Beam with Daytime Running
Lights (DRL)/Position Light/Low
Beam/Side Marker
2 — Front Indicator Light
3 — Fog Light
04110102-L40-010
Rear Lights
4 — Side Marker — If Equipped
5 — Position Light/Stop Light/Rear
Direction Indicator Light
6 — Reverse Light — If Equipped
7 — Third Stop Light
GUID-08020499000002
Mud Guard
1 — Fasteners
2 — Mud Guard
186
IN
CASE
OF
EMERGENCY
-------------------------------------------------------------------------------------------------------------------------------------------------------------
7. Install the new bulb in the reverse
order of the removal procedure.
Headlights (high beam) with
Daytime Running Lights
(If Equipped with LED Lamps)
Proceed as follows:
1. If you are changing the right bulb,
start the engine, turn the steering wheel
all the way to the right, and turn off
engine. If you are changing the left bulb,
turn the steering wheel to the left.
2. Make sure the ignition is placed in
the OFF mode, and the headlight
switch is off.
3. Remove the fasteners in the seven
locations and partially peel back the
mud guard.
4. Turn the socket and bulb assembly
counterclockwise and remove it.
5. Turn the cover counterclockwise and
remove it, disconnect the connector
from the unit by pressing the tab on the
connector with your finger and pulling
the connector.
6. Turn the socket and bulb assembly
counterclockwise and remove it.
7. Disconnect the bulb from the
socket.
8. Install the new bulb in the reverse
order of the removal procedure.
Front Direction Indicator Lights
Proceed as follows:
1. If you are changing the right bulb,
start the engine, turn the steering wheel
all the way to the right, and turn off
engine. If you are changing the left bulb,
turn the steering wheel to the left.
2. Make sure the ignition is switched
off, and the headlight switch is off.
3. Remove the fasteners in the five
locations and partially peel back the
mud guard.
4. Disconnect the connector from the
unit by pressing the tab on the
connector with your finger and pulling
the connector rearward.
GUID-08020499000010
Head Lamp Assembly
1 — High Beam Lamp
2 — Position Lamp
3 — Daytime Running Lamp
GUID-07031501206002
Mud Guard
187
-------------------------------------------------------------------------------------------------------------------------------------------------------------
5. Turn the socket and bulb assembly
counterclockwise and remove it.
6. Disconnect the bulb from the
socket.
7. Install the new bulb in the reverse
order of the removal procedure.
Fog Lights
Proceed as follows:
1. If you are changing the right bulb,
start the engine, turn the steering wheel
all the way to the right, and turn off
engine. If you are changing the left bulb,
turn the steering wheel to the left.
2. Make sure the ignition is switched
off, and the headlight switch is off.
3. Remove the fasteners in the five
locations and partially peel back the
mud guard.
4. Disconnect the connector from the
unit by pressing the tab on the
connector with your finger and pulling
the connector.
5. Turn the socket and bulb assembly
counterclockwise, extract the bulb and
remove it;
6. Disconnect the bulb from the
socket.
7. Install the new bulb in the reverse
order of the removal procedure.
Brake lights / Tail lights
Go to your authorized dealer when the
replacement of this lights is necessary.
Side Direction Indicator Lights
Proceed as follows:
1. Make sure the ignition is placed in
the OFF mode, and the headlight
switch is off.
2. If you are changing the right bulb,
start the engine, turn the steering wheel
all the way to the right, and turn off
engine. If you are changing the left bulb,
turn the steering wheel to the left.
3. Remove the fasteners in the five
locations and partially peel back the
mud guard.
4. Disconnect the electrical connector
from the bulb by pressing the tab on
the connector with your finger and
pulling the connector.
5. Remove the lens assembly by
pressing the tab on the unit with your
finger and pulling the unit forward to
compress in the internal catch, then pull
the cluster outwards.
6. Lift up the lens assembly, and then
remove the cluster and install the new
side direction indicator lens assembly in
the reverse order of the removal
procedure.
07031501-207-001
Front Direction Indicator Housing
1 — Socket Assembly
2 — Bulb
GUID-07031501208002
Direction Indicator Lamp Connector
188
IN
CASE
OF
EMERGENCY
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Front Side Marker
(If equipped with halogen bulb)
Proceed as follows:
1. Remove the fasteners in the seven
locations and partially peel back the
upper side of the mud guard.
2. Turn the socket counterclockwise,
remove socket assembly then remove
the bulb.
3. Install the new bulb in the reverse
order of the removal procedure.
GUID-08020499000011
Side Direction Indicator
1 — Fasteners
GUID-07031501210001
Side Direction Indicator
2 — Lens Assembly
GUID-07031501211001
Side Direction Indicator
3 — Internal Catch
4 — Lens Assembly
08070604-123-100
Front Side Marker
1 — Socket
2 — Bulb Assembly
189
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Rear Direction Indicator Lights
Proceed as follows:
1. Remove the retainers and the trunk
lid end trim.
2. Disconnect the connector from the
unit by pressing the tab on the
connector with your finger.
3. Remove the screw and nuts.
4. Pull the taillight housing rearward to
remove it.
07031501-212-002
Trunk Trim
1 — Retainers
GUID-07031501214002
Trunk Trim
2 — Connector
GUID-07031501213002
Rear Direction Indicator Socket
3 — Connector
07031501-215-001
Taillight Housing Fasteners
4 — Screw
5 — Nuts
190
IN
CASE
OF
EMERGENCY
-------------------------------------------------------------------------------------------------------------------------------------------------------------
5. Turn the socket and bulb assembly
counterclockwise to remove from
taillight housing, and remove bulb.
6. Install the new bulb in the reverse
order of the removal procedure.
Reverse Light
Proceed as follows:
1. Make sure the ignition is placed in
the OFF mode, and the headlight
switch is off.
2. Turn the socket assembly
counterclockwise to remove, and
remove bulb.
3. Install the new bulb in the reverse
order of the removal procedure.
Rear Side Marker
Proceed as follows:
1. Push the lens assembly rearward to
compress the internal catch, then pull
the lens assembly outwards.
2. Turn the socket and bulb assembly
counterclockwise to remove, and
remove bulb.
07031501-216-001
Rear of Vehicle
6 — Taillight Housing
07031501-203-002
Taillight Housing
7 — Socket and Bulb Assembly
07031501-219-001
Reverse Light
1 — Socket Assembly
2 — Bulb
08070605-123-100
Rear Side Marker
1 — Rear Side Marker Lens Assembly
191
-------------------------------------------------------------------------------------------------------------------------------------------------------------
3. Install the new bulb and then
reinstall the socket in the reverse order
of the removal procedure.
License Plate Lights
Proceed as follows:
1. Make sure the ignition is placed in
the OFF mode, and the headlight
switch is off.
2. Slide the unit as shown in the figure
to remove it.
3. Turn the socket and bulb assembly
counterclockwise and remove, remove
bulb.
4. Install the new bulb in the reverse
order of the removal procedure. Insert
catch and push the housing back into
place.
08070606-123-100
Side Marker Housing
2 — Socket and Bulb Assembly
GUID-07031501220001
Trunk Lid
1 — License Plate Light Assembly
07031501-221-001
License Plate Light Housing
2 — Socket and Bulb Assembly
192
IN
CASE
OF
EMERGENCY
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Replacing Interior Light
Bulbs
Overhead Light
Proceed as follows:
1. Using a suitable tool to prevent
damage to the lens, remove the
overhead light by carefully prying on the
edge of the lens.
2. Disconnect the bulb by pulling it out.
3. Install the new bulb in the reverse
order of the removal procedure.
Trunk Light
Proceed as follows:
1. Using a suitable tool to prevent
damage to the to the lens, remove the
trunk light lens by carefully prying on
the edge of the lens.
2. Disconnect the connector from the
trunk light lens.
3. Disconnect the bulb by pulling it out.
4. Install the new bulb in the reverse
order of the removal procedure.
07031502-201-001
Overhead Light Location
1 — Overhead Light Lens
07031502-202-001
Trunk Light
1 — Trunk Light Lens
07031502-203-001
Trunk Light Housing
2 — Connector
193
-------------------------------------------------------------------------------------------------------------------------------------------------------------
REPLACING FUSES
General Information
Warning!
When replacing a blown fuse, always
use an appropriate replacement fuse with
the same amp rating as the original fuse.
Never replace a fuse with another fuse of
higher amp rating. Never replace a blown
fuse with metal wires or any other material.
Failure to use proper fuses may result in
serious personal injury, fire and/or property
damage.
Before replacing a fuse, make sure that
the ignition is off and that all the other
services are switched off and/or
disengaged.
If the replaced fuse blows again, contact
an authorized dealer.
If a general protection fuse for safety
systems (air bag system, braking system),
power unit systems (engine system,
gearbox system) or steering system blows,
contact an authorized dealer.
Your vehicle's electrical system is
protected by fuses.
If any lights, accessories, or controls do
not work, inspect the appropriate circuit
protector. If a fuse has blown, the inside
element will be melted. If the same fuse
blows again, go to an Authorized Dealer
as soon as possible.
Fuse location
Fuses are grouped together in two fuse
boxes located in the interior on the left
side of the vehicle and under the hood.
Interior Fuses
If the electrical system does not work,
first inspect the fuses on the vehicle's
left side.
Proceed as follows:
1. Make sure the ignition is placed in
the OFF mode, and other switches are
turned off.
2. Open the fuse panel cover (located
near the door).
3. Press retaining clip and remove
protection cover.
4. Pull the fuse straight out with the
fuse puller provided on the fuse block
located in the engine compartment.
5. Inspect the fuse and replace it if it is
blown.
07031601-121-001
Fuse Panel Cover
07031601-122-001
Fuse Puller
194
IN
CASE
OF
EMERGENCY
-------------------------------------------------------------------------------------------------------------------------------------------------------------
6. Insert a new fuse of the same
amperage rating, and make sure it fits
tightly. If it does not fit tightly, contact an
Authorized Dealer. If you have no spare
fuses, borrow one of the same rating
from a circuit not essential to vehicle
operation, such as the audio or outlet
circuit.
7. Reinstall the cover and make sure
that it is securely installed.
Note: Always replace a fuse with a
genuine FCA fuse or equivalent of the
same rating. Otherwise you may
damage the electric system.
Underhood Fuses
If the headlights or other electrical
components do not work and the fuses
in the cabin are normal, inspect the fuse
block in the engine compartment. If a
fuse is blown, it must be replaced.
Make sure the ignition is placed in the
OFF mode, and other switches are
turned off and remove the fuse block
cover. If the lock is forcefully opened,
the fuse block cover may come in
contact with the frame when it is
removed and become scratched.
When removing the cover, remove it
slowly according to the following
procedure:
1. Disengage the rear lock by pressing
down on the front tab with your fingers.
2. Remove the front tab while slightly
lifting the front of the cover.
3. Remove the cover while lifting it and
sliding it to the rear.
4. If any fuse but the main fuse is
blown, replace it with a new one of the
same amperage rating.
5. Reinstall the cover and make sure
that it is securely installed.
07031601-ALL-001
Fuses
1 — Normal Fuse
2 — Blown Fuse
07031601-123-001
Underhood Fuse Block
1 — Lock
2 — Cover
07031601-ALL-002
Fuse
1 — Normal Fuse
2 — Blown Fuse
195
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Fuse Block (Engine Compartment)
07031602-121-001
196
IN
CASE
OF
EMERGENCY
-------------------------------------------------------------------------------------------------------------------------------------------------------------
DESCRIPTION
FUSE RATING
PROTECTED COMPONENT
F01
ENG IG3
5 A
Engine control systems
F02
ENG IG2
5 A
Engine control systems
F03
HORN2
7.5 A
Horn
F04
C/U IG1
15 A
For protection of various circuits
F05
ENG IG1
7.5 A
Engine control system
F06
—
—
—
F07
INTERIOR
15 A
Overhead light
F08
—
—
—
F09
AUDIO2
15 A
Audio system
F10
METER1
10 A
Instrument cluster
F11
SRS1
7.5 A
Air bag
F12
—
—
—
F13
RADIO
7.5 A
Audio system
F14
ENGINE3
20 A
Engine control system
F15
ENGINE1
10 A
Engine control system
F16
ENGINE2
15 A
Engine control system
F17
AUDIO1
25 A
Audio system
F18
A/C MAG
7.5 A
Air conditioner
F19
AT PUMP H/L HI
20 A
Transmission control system (IF Equipped)
F20
AT
15 A
Transmission control system (If Equipped)
F21
D LOCK
25 A
Power door locks
F22
H/L RH
20 A
Headlight (RH)
F23
ENG + B2
7.5 A
Engine control system
197
-------------------------------------------------------------------------------------------------------------------------------------------------------------
DESCRIPTION
FUSE RATING
PROTECTED COMPONENT
F24
TAIL
20 A
Taillights/Number plate lights/Position lights
F25
—
—
—
F26
ROOM
25 A
Overhead light
F27
FOG
15 A
Fog Lights
F28
H/CLEAN
20 A
Headlight washer (If — Equipped)
F29
STOP
10 A
Stop lights/Rear fog light (If Equipped)
F30
HORN
15 A
Horn
F31
H/L LH
20 A
Headlight (LH)
F32
ABS/DSC S
30 A
ABS/DSC system
F33
HAZARD
15 A
Hazard warning flashers/Direction indicators lights
F34
FUEL PUMP
15 A
Fuel system
F35
ENG + B3
5 A
Engine control system
F36
WIPER
20 A
Windshield wipers
F37
CABIN + B
50 A
For protection of various circuits
F38
—
—
—
F39
—
—
—
F40
ABS/DSC M
50 A
ABS/DSC system
F41
EVVT A/R PUMP
20 A
Engine control system
F42
—
—
—
F43
—
—
—
F44
FAN2
40 A
Cooling Fan
F45
ENG.MAIN
40 A
Engine control system
F46
EPS
60 A
Power steering system
198
IN
CASE
OF
EMERGENCY
-------------------------------------------------------------------------------------------------------------------------------------------------------------
DESCRIPTION
FUSE RATING
PROTECTED COMPONENT
F47
DEFOG
30 A
Rear window defogger
F48
IG2
30 A
For protection of various circuits
F49
—
—
—
F50
HEATER
40 A
Air conditioner
F51
—
—
—
F52
—
—
—
199
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Fuse Block Interior
07031602-03F-002
200
IN
CASE
OF
EMERGENCY
-------------------------------------------------------------------------------------------------------------------------------------------------------------