Daewoo Korando. Instruction - page 358
SWITCHES 9V-5
5. Unscrew the 3 screws from the steering column shaft lower
cover and remove both upper and lower covers.
6. Unscrew the 4 screws of clock spring and remove the clock
spring.
Notice
Refer to clock spring removal for its installation notes.
7. Unscrew the 3 screws and remove the multifunction switch.
8. Installation should follow the removal procedure in the
reverse order.
9V-6 SWITCHES
(Light switch connector)
(Wiper and washer switch connector)
0.3R
Connector Terminal Number & Circuit
NO. Circuit
Wiring
Item
1
EB
2.0B
Head lamp beam ground
2
HU
2.0RL
Head Lamp Upper Beam Power
3
HL
2.0R
Head Lamp Lower Beam Power
4
TS
0.3R
Tail Lamp Switch
5
HS(1)
0.3LW
Head Lamp Switch
6
HS(2)
1.25LW
Head Lamp Switch Passing
7
TB
0.85GR
Flasher Unit Power
8
TL
0.5W
Turn Signal Lamp (LH)
9
TR
0.5Y
Turn Signal Lamp (RH)
10
ES
0.3B
Head lamp Switch Ground
11
HO
0.5BW
Horn
12
WA
0.5LY
Washer
13
P
0.85GB
Wiper Parking
14
HI
0.85RB
Wiper High Speed
15
INT
0.5G
Intermittent Wiper
16
LO
0.85GR
Wiper Speed (LO)
17
ES
0.85B
Wiper and Washer Ground
18
-
-
-
19
F(2)
0.3Br
Front Fog Lamp
20
FR
0.3G
Front fog Lamp Ground
21
-
-
-
22
-
-
-
23
-
-
-
24
-
-
-
25
HO
0.5GR
Horn
26
ES
0.5BW
Remote Control Ground
27
AUD
0.5Y
Remote Control Signal
28
ACC
0.5L
Remote Control Switch
29
DSL
0.5f L
Driver’s Inflator (LOW)
30
DSH
0.5f Br
Driver’s Inflator (HIGH)
37
E(T)
0.3BY
Intermittent Wiper Ground
38
INT(T)
Intermittent Wiper
SWITCHES 9V-7
Check and Service
After disconnecting the connectors, operate the multifunction
switch and check each terminals for current flow.
Light Switch
Head Lamp
Terminal No.
1
2
3
4
5
6
7
8
9
10 19 20
OFF
Tail
Head
OFF
LH
RH
Passing
LOWER
UPPER
OFF
ON
Turn Signal
Dimmer and
Passing
Front Fog
Lamp
Front Wiper
and Washer
Switch
Terminal No.
12 13 14 15 16 17 21 22 23 24
OFF
AUTO
LO
HI
Washer
Wiper and Washer Switch
Switch
Switch
37 38
®
9V-8 SWITCHES
OTHER SWITCHES
Maintenance and repair
(Tailgate Glass Defogger)
1. Check the defogger
Before checking the electric equipment’s, usually disconnect
the battery negative(-) terminal.
1) Check the tailgate defogger after battery is fully charged
by running the engine at idle speed.
2) Check the heated wire voltage at tailgate glass center
position “A” by using circuit tester when the tailgate glass
defogger switch is “ON”. If the voltage is approx. 6V, the
system is normal.
3) If the voltage indicates 12V at point “A” , it is considered
that there is a short between “A” and (-) terminal.
4)Find out where the voltage abruptly changes to the 0V by
moving tester bar to the (-) terminal side slightly.
5) If the voltage indicates 0V at point “A”, it is considered
that there is a short between “A” and (+) terminal.
6) Find out where the voltage abruptly changes to the 12V
by moving tester bar to the (-) terminal side slightly.
2. Checking the switch
1) Remove the tailgate glass defogger switch wire from
instrument panel.
2) Turn on the switch and carry out the continuity test
between terminals.
Notice
:
It means the electrical continuity between
terminals.
3. Checking the relay
Remove the tailgate glass defogger relay from the relay
box.
Switch position
OFF
ON
1
4
2
5
6
Terminal NO.
