Daewoo Korando. Instruction - page 357
SECTION 9V
SWITCHES
Caution: Disconnect the negative battery cable before removing or installing any electrical unit or when a
tool or equipment could easily come in contact with exposed electrical terminals. Disconnecting this cable
will help prevent personal injury and damage to the vehicle. The ignition must also be in LOCK unless otherwise
noted.
TABLE OF CONTENTS
Specifications . . . . . . . . . . . . . . . . . . . . . . . . 9V-1
General Specifications . . . . . . . . . . . . . . . . . . 9V-1
Component Locator . . . . . . . . . . . . . . . . . . . 9V-2
Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9V-2
Maintenance and Repair . . . . . . . . . . . . . . . 9V-4
On-Vehicle Service . . . . . . . . . . . . . . . . . . . . . . 9V-4
Combination Switch . . . . . . . . . . . . . . . . . . . . 9V-4
Other Switches . . . . . . . . . . . . . . . . . . . . . . . . 9V-8
SPECIFICATIONS
GENERAL SPECIFICATIONS
Description
each 0.2 - 0.3A
0.8 - 1.7Kgf·Cm
Axial:less than 1.0mm, Radial:less than 1.5mm
each 6.1 - 6.7A
Less than 2.5mm in width from the lever end
HU:15A, HL:10A, P:20A
INT:0.25±0.05A
LO:6A, HI:8A, LOCK:max. 23A
Less than 2.5mm in width from the lever end
4A
Max. : 7A
0.2 - 0.3A
Max. : 25mA
Load Rating (relay load)
Operating Force (knob rotation)
Free Play
Load Rating (Lamp Load)
Free Play
Load Rating(Each Lamps Load)
Load Rating(Relay Load)
Load Rating(Motor Load)
Free Play
Light Switch
Turn Signal
lamp Switch
Dimmer and
Passing Switch
Wiper Switch
Washer Switch (Motor Load Rating)
Horn Contact Load Rating
Front Fog Lamp Switch Load Rating
Variable INT Volume Switch
Application
9V-2 SWITCHES
COMPONENT LOCATOR
SWITCHES
1 -
2 Hazard Switch
3 Rear Heated Window Switch
4 Center Fascia Switch Cover
5 -
6 ECS Switch
7 Glove Box Switch
8 Air-Conditioner Panel Assembly
9 Rear Wiper And Washer Switch
10 4WD Switch
11 4WD Switch Cover
12 Kick Down Switch(4P)
13 Outside Mirror Switch
14 Head Lamp Leveling Switch Assembly
(Optional Item)
SWITCHES 9V-3
15 Hood Switch
16 Door Switch
17 Tail Gate Switch
18 Atmospheric Sensor
19 Sun Light Sensor Assembly
20 Speed Sensor Assembly
21 Power Window Main Switch
22 Power Window Sub Switch
23 Band
24 Multi-Function Switch Assembly
25 Blanking Cover
9V-4 SWITCHES
COMBINATION SWITCH
Removal & Installation Procedure
1. Turn the ignition switch to ‘OFF’ position, disconnect the
negative battery cable and go next step after waiting at least
30 seconds.
2. Separate both left and right covers from the steering wheel
and unscrew 2 bolts(10mm)
Installation Notice
3. Disconnect steering wheel audio remote control connector,
horn connector and airbag module connector and remove
the airbag module.
Notice
Refer to airbag module removal.
4. Mark the alignment marks on the steering nut and upper
column shaft and unscrew nut (22mm).
Installation Notice
Tightening Torque
7 - 11 Nm
Tightening Torque
50 - 80 Nm
MAINTENANCE AND REPAIR
ON-VEHICLE SERVICE
