Daewoo Korando. Instruction - page 219
Application
SECTION 3C
PROPELLER SHAFT
TABLE OF CONTENTS
Specifications . . . . . . . . . . . . . . . . . . . . . . . . 3C-1
General Specifications . . . . . . . . . . . . . . . . . . 3C-1
Component Locator . . . . . . . . . . . . . . . . . . . 3C-2
M/T & A/T (Part-time T/C) . . . . . . . . . . . . . . . . 3C-2
Maintenance and Repair . . . . . . . . . . . . . . . 3C-3
On-Vehicle Service . . . . . . . . . . . . . . . . . . . . . 3C-3
Propeller Shaft . . . . . . . . . . . . . . . . . . . . . . . . 3C-3
SPECIFICATIONS
GENERAL SPECIFICATIONS
Description
Construction
Joint Type
Number of Spider
Tube Run-Out
(after installation)
Front Shaft Dimension
(L
´
I.D
´
O.D)
Rear Shaft Dimension
(L
´
I.D
´
O.D)
Universal Joint with Yoke and Spider
Spider (Needle Roller Bearing)
3
2
Within 0.3 mm
Within 0.4 mm
579
´
f
59.5
´
f
63.5
583.5
´
f
44.7
´
f
50.8
617.6
´
f
44.7
´
f
50.8
595.6
´
f
44.7
´
f
50.8
824
´
f
59.5
´
f
63.5
777
´
f
59.5
´
f
63.5
Front (Part-Time T/C)
Rear
E 32 Engine
The Others
Diesel + M/T & A/T + 4408
M161 + M/T & A/T + 4408
M161 + M/T & A/T
Diesel & M161 + M/T & A/T + 4408
M162 + M/T & A/T + TOD
Tongil
KSC
3C-2 PROPELLER SHAFT
1 Flange Yoke
2,3 3-Journal Cross and Bearing Kit (Including Snap
Ring)
4 Slip Yoke Assembly
5 Grease Nipple
6 Dust Cap
7 Oil Seal
8 Split Washer
9 Slip Tube Shaft
10 Tube
11 Tube Yoke
12 Flange Yoke
Notice
Only the length of shaft is different and the components of front/rear shaft are the same.
(The deadener is inserted to the inside of tube of rear shaft, both ends)
COMPONENT LOCATOR
M/T & A/T (PART-TIME T/C)
PROPELLER SHAFT 3C-3
1 Front Axle
2 Bolt ...................................................... 70-80 Nm
3 Front Propeller Shaft (661LA/662LA)
4 Front Propeller Shaft (E32)
5 Bolt ...................................................... 81-89 Nm
MAINTENANCE AND REPAIR
ON-VEHICLE SERVICE
PROPELLER SHAFT
6 Transfer Case
7 Bolt ...................................................... 81-89 Nm
8 Rear Propeller Shaft
9 Bolt ...................................................... 70-80 Nm
10 Rear Axle
11 Front Propeller Shaft (E20/E23)
3C-4 PROPELLER SHAFT
Removal Procedure
1. Place alignment marks and remove the propeller shaft.
2. Place alignment marks before removing the spider.
3. Using a snap ring pliers, remove the snap ring.
4. Slightly tapping the yoke shoulder using a brass hammer,
remove the bearing. Remove the remaining bearings in the
same way.
