Daewoo Korando. Instruction - page 119
1B3-186 OM600 ENGINE MECHANICAL
Installation of screw plug
Notice
If steel ball leaks again, install the screw plug.
1. Remove the steel ball.
2. Tap thread into the bores of the oil gallery.
Notice
Front bore : M18 ´ 1.5, depth 10mm
Rear bore : M16 ´ 1.5, depth 14mm
3. Thoroughly clean the oil gallery.
4. Tighten the front plug (5) with seal (4).
5. Apply Loctite 241 and then tighten the rear plug (2).
Tightening Torque
50 Nm
Tightening Torque
50 Nm
OM600 ENGINE MECHANICAL 1B3-187
Standard size
Wear limit in direction of travel and in transverse direction
Permissible deviation of cylinder shape
Honing angle
CYLINDER BORE MEASUREMENT
a
Longitudinal Direction
b
Transverse Direction
c, d, e. Measuring Point
1
Crankcase Contacting Surface
2
TDC of 1st Piston Ring
4
BDC of Ring
Service Data
Code letter ‘A’
Code letter ‘X’
Code letter ‘B’
-
When new
Wear limit
-
89.000 - 89.006mm
89.006 - 89.012mm
89.012 - 89.018mm
Max. 0.20mm
0.01mm
0.05mm
50° ± 10°
SECTION 1D1
M162 ENGINE COOLING
Specifications . . . . . . . . . . . . . . . . . . . . . . . 1D1-1
General Specifications . . . . . . . . . . . . . . . . . 1D1-1
Fastener Tightening Specifications . . . . . . . . 1D1-2
Special Tools . . . . . . . . . . . . . . . . . . . . . . . 1D1-3
Special Tools Table . . . . . . . . . . . . . . . . . . . . 1D1-3
Diagnosis . . . . . . . . . . . . . . . . . . . . . . . . . . 1D1-4
System Leakage Test . . . . . . . . . . . . . . . . . . 1D1-4
Maintenance and Repair . . . . . . . . . . . . . . 1D1-5
On-Vehicle Service . . . . . . . . . . . . . . . . . . . . 1D1-5
Coolant Drain and Fill Up . . . . . . . . . . . . . . . 1D1-5
Coolant Connection Fitting . . . . . . . . . . . . . . 1D1-7
Water Pump . . . . . . . . . . . . . . . . . . . . . . . . . 1D1-8
Thermostat . . . . . . . . . . . . . . . . . . . . . . . . . 1D1-10
Oil Cooler Pipe Line . . . . . . . . . . . . . . . . . . 1D1-11
Cooling Fan and Viscous Clutch . . . . . . . . . 1D1-12
Cooling Fan Shroud . . . . . . . . . . . . . . . . . . 1D1-14
Radiator . . . . . . . . . . . . . . . . . . . . . . . . . . . 1D1-15
SPECIFICATIONS
GENERAL SPECIFICATIONS
CAUTION: Disconnect the negative battery cable before removing or installing any electrical unit or when a
tool or equipment could easily come in contact with exposed electrical terminals. Disconnecting this cable
will help prevent personal injury and damage to the vehicle. The ignition must also be in LOCK unless otherwise
noted.
TABLE OF CONTENTS
Description
Water Cooling Forced Circulation
Double Cross Flow
70,000 kcal/h
580 x 482 x 45 mm
f
460, Six Blades
ALUTEC - P78
50 : 50
11.3 L
3.4 L
1.4 bar
Application
Cooling Type
Radiator
Dimension(Width
´
Height
´
Thickeness)
Cooling Fan
Anti-Freeze Agent
Mixing Ratio of Anti-Freeze Agen with Water (Anti-Freeze Agent : Water)
Coolant Capacity
Reservoir Capacity
Cap Operating Pressure (Reservoir Tank Pressure Cap)
Circulation Type
Radiation Capability
1D1-2 M162 ENGINE COOLING
FASTENER TIGHTENING SPECIFICATIONS
N
·
·
·
·
·
m
30
22.5 - 27.5
9 - 11
9 - 11
9 - 11
40.5 - 49.5
3 - 7
3 - 7
Application
Coolant Drain Plug
Engine Hanger Bracket and Coolant Outlet
Port Bolt
Thermostat Cover Bracket Bolt
Oil Cooler Pipe Line Bolt
Cooling Fan Bolt
Viscous Clutch Bolt
Automatic Transmission Oil Cooling Hose Bolt
Cooling Fan Shroud Bolt
