DAF CF65, CF75, CF85 Series . Instruction - page 23
©
1-3
VIC fault codes
VIC
DAVIE XD diagnostics manual
4
13404-24
Short circuit to earth or excessive load on pin E04
of the ECU
-
Prime mover right flasher lights: not flashing
at the rear, flashing with too high a
frequency at the front
13404-5
Interruption or insufficient load on pin E04 of the
ECU
-
Prime mover right flasher lights are not
working
13405-24
Short circuit to earth or excessive load on pin A07
of the ECU
-
Drawn vehicle left flasher lights are not
working
13406-24
Short circuit to earth or excessive load on pin A08
of the ECU
-
Drawn vehicle right flasher lights are not
working
21301-3
Short circuit to supply on pin D16 of the ECU
-
Air pressure gauge, circuit 1, gives no
reading
21301-20
Interruption or short circuit to earth on pin D16 of
the ECU
-
Air pressure gauge, circuit 1, gives no
reading
21301-23
Voltage out of range; voltage between 0 and 1 V
on pin D16 of the ECU
-
Air pressure gauge, circuit 1, gives no
reading
21301-25
Voltage out of range; voltage between 4 and 5 V
on pin D16 of the ECU
-
Air pressure gauge, circuit 1, gives no
reading
21302-3
Short circuit to supply on pin D11 of the ECU
-
Air pressure gauge, circuit 1, gives no
reading
21302-20
Interruption or short circuit to earth on pin D11 of
the ECU
-
Air pressure gauge, circuit 2, gives no
reading
21302-23
Voltage out of range; voltage between 0 and 1 V
on pin D11 of the ECU
-
Air pressure gauge, circuit 2, gives no
reading
21302-25
Voltage out of range; voltage between 4 and 5 V
on pin D11 of the ECU
-
Air pressure gauge, circuit 2, gives no
reading
21303-3
Short circuit to supply on pin D31 of the ECU
-
Air pressure gauges, circuits 1 and 2, give
no reading
21303-4
Short circuit to earth on pin D31 of the ECU
-
Flashing instrument lighting on DIP-4, no
possibility to read fault codes
21901-3
Short circuit to supply on pin B24 of the ECU
-
The traction control can be activated
independently of speed; normally the
traction control can no longer be activated
above 30 km/h
22001-21
Interruption on pin C05 of the ECU or interruption
in the voltage supply
-
Rear fog light relay is no longer
automatically deactivated when the lighting
is switched off
22002-3
Short circuit to supply on pin C40 of the ECU
-
Rear fog lights remain lit, irrespective of the
position of the switch
22002-20
Interruption or short circuit to earth on pin C40 of
the ECU
-
Rear fog lights are not working
22601-21
Interruption on pin C08 of the ECU
-
No glow indication on DIP-4
22901-22
Interruption or short circuit to supply on pin D15 of
the ECU
-
Yellow warning "Coolant level low" is
activated
22901-23
Voltage signal is outside of tolerance field
-
Information on the main display does not
correspond with the actual coolant level; a
warning may be displayed
23801-4
Short circuit to earth on pin D04 of the ECU
-
Instrument lighting can no longer be dimmed
Fault code
Fault code description with possible cause
Symptom
VIC
1-4
©
VIC fault codes
4
DAVIE XD diagnostics manual
23801-5
Interruption or insufficient load on pin D04 of the
ECU
-
Instrument lighting can no longer be dimmed
23802-21
Interruption on pin C07 of the ECU
-
Instrument lighting can no longer be dimmed
24202-19
No CAN message received from transmission
ECU due to:
-
communication problem with transmission
ECU
-
No noticeable system limitation in VIC
24204-19
No CAN message received from intarder ECU
due to:
-
communication problem with intarder ECU
-
No noticeable system limitation in VIC
24401-2
Fault when reading the chassis number
-
Red warning "VIC configuration fault"
25601-16
Engine speed too high
-
Yellow warning "engine speed too high" is
active; the engine speed is higher than
2450 rpm for more than 1 second
26001-3
Short circuit to supply on pin B23 of the ECU
(manually operated gearbox)
-
PTO 1 is permanently activated
26001-20
Interruption or short circuit to earth on pin B23 of
the ECU (manually operated gearbox)
-
PTO 1 is not activated upon operation of the
switch; also, a yellow PTO 1 warning
becomes active
26002-3
Short circuit to supply on pin C46 of the ECU
(manually operated gearbox)
-
PTO 2 is permanently activated
26002-20
Interruption or short circuit to earth on pin C46 of
the ECU (manually operated gearbox)
-
PTO 2 is not activated upon operation of the
switch; also, a yellow PTO 2 warning
becomes active
26101-11
No signal on pin B01/B07 of the ECU of the
engine oil level sensor (F673)
-
Red warning "engine oil level too low" is
activated
26201-3
Short circuit to supply on pin B23 of the ECU
(AS Tronic)
-
PTO 1 is permanently activated
26201-20
Interruption or short circuit to earth on pin B23 of
the ECU (AS Tronic)
-
PTO 1 is not activated upon operation of the
switch; also, a yellow PTO 1 warning
becomes active
26202-3
Short circuit to supply on pin C46 of the ECU
(AS Tronic)
-
PTO 2 is permanently activated
26202-20
Interruption or short circuit to earth on pin C46 of
the ECU (AS Tronic)
-
PTO 2 is not activated upon operation of the
switch; also, a yellow PTO 2 warning
becomes active
27201-3
Short circuit to supply on pin C42 of the ECU
-
Engine cannot be started; relay G372/G303
remains energised (depending on the
production date, this connection is on pin
C44 of the ECU with vehicles
2004-25)
-
Lighting remains lit, relay G301 remains
energised
-
Cab heater cannot be switched on, relay
D871/D901 remains energised
Fault code
Fault code description with possible cause
Symptom
©
1-5
VIC fault codes
VIC
DAVIE XD diagnostics manual
4
27201-19
No CAN message received "engine speed"
There is no power supply on output C42 so that
-
there is no start protection when the engine
is running; relay G303/G372 cannot be
energised
-
Swedish lighting is not working; relay G301
cannot be energised
-
the cab heater is not switched off; relay
D871/D901 is not energised
27201-20
Interruption or short circuit to earth on pin C42 of
the ECU
-
There is no start protection when the engine
is running; relay G303/G372 cannot be
energised
-
Swedish lighting is not working; relay G301
cannot be energised
-
The cab heater is not switched off; relay
D871/D901 is not energised
30801-2
Interruption of power supply on pin A02 of the
ECU
-
Alarm light function is not working
30802-2
Interruption of power supply on pin A09 of the
ECU
-
Alarm light function is not working
30803-2
Interruption of power supply on pin E03 of the
ECU
-
Direction indicator function is not working
33301-19
No CAN message received from CAN extension
box due to:
-
communication problem with CAN extension
box
-
No noticeable system limitation in VIC
Fault code
Fault code description with possible cause
Symptom
VIC
1-6
©
VIC fault codes
4
DAVIE XD diagnostics manual