Audi TT (2007 year). Instruction - page 11

Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by AUDI AG.

– Initially hand-tighten bolts -arrows- for assembly mounting

(gearbox end) as far as stop.

Note

The bolts are tightened to final torque only after adjusting the as‐

sembly mountings

⇒ page 39

.

– Remove engine support -T10012- from engine.
– Install pump for exhaust gas recirculation cooler -V400-

⇒ page 175

.

– Install air pipe

⇒ page 208

.

– Install particulate filter

⇒ page 218

.

– Secure propshaft with flexible coupling to bevel box flange ⇒

⇒ page 44

.

⇒ page 191

.

– Install radiator cowl

⇒ page 192

.

– Connect coolant hoses with plug-in connector to heat ex‐

changer

⇒ page 191

.

⇒ page 209

.

34 .

– Adjust assembly mountings

⇒ page 39

.

– Electrical connections and routing ⇒ Current flow diagrams,

Electrical fault finding and Fitting locations.

– Observe notes on procedure for connecting the battery ⇒ Rep.

Gr. 27 .

Caution

Risk of damage to control units because of excessive voltage.

♦ Never use battery charging equipment for boost starting.

– Fill up with coolant

⇒ page 166

.

4. Installing engine

35

Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by AUDI AG.

Note

Do not use drained coolant again if:

the cylinder head or cylinder block have been renewed.

the coolant is contaminated or dirty.

36

Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by AUDI AG.

5

Assembly mountings

5.1

Assembly mountings - exploded view

1 - Bolt

❑ Gearbox support to

gearbox

❑ Tightening torque ⇒

Rep. Gr. 34 ⇒ Rep. Gr.

37

2 - Bolts

❑ Pendulum support to

gearbox

❑ Tightening torque ⇒

Rep. Gr. 34 ⇒ Rep. Gr.

37

3 - Engine support

❑ With support arm
❑ Version fitted in vehicle

may differ from illustra‐

tion

4 - Bolt

❑ Engine support to en‐

gine

❑ Observe correct tighten‐

ing sequence

⇒ page 38

❑ 40 Nm + 180°

5 - Engine mounting
6 - Bolt

❑ Engine mounting to

body

❑ Renew
❑ 40 Nm + 90°

7 - Connecting bracket
8 - Bolt

❑ Connecting bracket to engine mounting
❑ Renew
❑ 20 Nm + 90°

9 - Bolt

❑ Connecting bracket to body
❑ Renew
❑ 20 Nm + 90°

10 - Bolt

❑ Engine mounting to body
❑ Renew
❑ 40 Nm + 90°

11 - Bolts

❑ Engine mounting to engine support

5. Assembly mountings

37

Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not
permitted unless authorised by AUDI AG. AUDI AG does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by AUDI AG.

❑ Renew
❑ 60 Nm + 90°

12 - Pendulum support
13 - Bolt

14 - Bolt

15 - Bolt

16 - Gearbox mounting

❑ With support arm

17 - Bolt

18 - Gearbox bracket

Tightening sequence for gearbox support
1 - Screw in bolts in the sequence -1, 2, 3- hand-tight.
2 - Tighten bolts in the sequence -1, 2, 3- to 40 Nm.
3 - Turn bolts in the sequence -1, 2, 3- 180° further.

5.2

Checking adjustment of assembly

mountings (engine/gearbox mountings)

Procedure
– Remove engine cover panel -arrows-.

38

Рассказать друзьям